Eaton FP1010V1-R120-R 120 nH Power Inductor, 68 A
Eaton FP1010V1-R120-R 120 nH Power Inductor, 68 A

Eaton FP1010V1-R120-R 120 nH Power Inductor, 68 A

Share
pEaton FP1010V1-R120-R: 120 nH high frequency, high current power inductor, 68 A Irms, 80 A Isat, DCR 0.145 mOhm, 10.0 x 7.0 mm package./p
    • Product Details
    • Download

    FP1010V1-R120-R at a glance: 120 nH high frequency, high current power inductor, 68 A Irms, 80 A Isat, DCR 0.145 mOhm, 10.0 x 7.0 mm body, 10.0 mm tall.

    Eaton FP1010V1-R120-R High frequency, high current power inductors

    FP1010V1-R120-R is one of Eaton's high frequency, high current power inductor series, 10.0 x 7.0 mm with a 10.0 mm tall profile. Electrically it offers 120 nH at 68 A Irms and 0.145 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Specification Table

    Orderable part numberFP1010V1-R120-R
    Inductance, OCL (0 Adc)120 nH
    Inductance, FLL (minimum)86 nH
    Irms (40 °C rise, no core loss)68 A
    Isat (20% roll-off @ +25 °C)80 A
    Isat2 (20% roll-off @ +75 °C)73 A
    Isat3 (20% roll-off @ +100 °C)71 A
    DCR typical @ +20 °C0.145 mOhm
    K-factor (Bp-p = K x L x dI)352
    Package10.0 x 7.0 mm, 10.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    The Figures Explained

    120 nH open-circuit, 86 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Peak current at 20% roll-off is 80 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Copper loss at the rated current works out at about 670 mW (68 A squared times 0.145 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The K-factor of 352 turns ripple into flux: a peak-to-peak swing of 24 A gives about 101.4 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Positioning in the FP Range

    The 10.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 120 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 3 of 11 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.145 mOhm, Irms of 68 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high- power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    The order of checks that works: compute ripple from 120 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.145 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1010V1-R120-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message