Eaton FP1010V1-R150-R - 150 nH Shielded Power Inductor 10.0 x 7.0 mm
Eaton FP1010V1-R150-R - 150 nH Shielded Power Inductor 10.0 x 7.0 mm

Eaton FP1010V1-R150-R - 150 nH Shielded Power Inductor 10.0 x 7.0 mm

Share
pEaton FP1010V1-R150-R: 150 nH high frequency, high current power inductor, 68 A Irms, 65 A Isat, DCR 0.145 mOhm, 10.0 x 7.0 mm package./p
    • Product Details
    • Download

    FP1010V1-R150-R at a glance: 150 nH high frequency, high current power inductor, 68 A Irms, 65 A Isat, DCR 0.145 mOhm, 10.0 x 7.0 mm body, 10.0 mm tall.

    Eaton FP1010V1-R150-R High frequency, high current power inductors

    FP1010V1-R150-R is one of Eaton's high frequency, high current power inductor series, 10.0 x 7.0 mm with a 10.0 mm tall profile. Electrically it offers 150 nH at 68 A Irms and 0.145 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Specification Table

    Orderable part numberFP1010V1-R150-R
    Inductance, OCL (0 Adc)150 nH
    Inductance, FLL (minimum)108 nH
    Irms (40 °C rise, no core loss)68 A
    Isat (20% roll-off @ +25 °C)65 A
    Isat2 (20% roll-off @ +75 °C)59 A
    Isat3 (20% roll-off @ +100 °C)57 A
    DCR typical @ +20 °C0.145 mOhm
    K-factor (Bp-p = K x L x dI)352
    Package10.0 x 7.0 mm, 10.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    At zero bias the winding measures 150 nH. Put Isat1 through it and the figure falls to 108 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 150 nH number; loop stability and worst-case current belong on the lower one.

    Saturation is quoted as 20% roll-off at 65 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Copper loss at the rated current works out at about 670 mW (68 A squared times 0.145 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The K-factor of 352 turns ripple into flux: a peak-to-peak swing of 19.5 A gives about 103 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Series Positioning

    The 10.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 150 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 5 of 11 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.145 mOhm, Irms of 68 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high- power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 150 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.145 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1010V1-R150-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products