Eaton FP1010V1-R180-R High Current Inductor, 180 nH 0.145 mOhm
Eaton FP1010V1-R180-R High Current Inductor, 180 nH 0.145 mOhm

Eaton FP1010V1-R180-R High Current Inductor, 180 nH 0.145 mOhm

Share
pEaton FP1010V1-R180-R: 180 nH high frequency, high current power inductor, 68 A Irms, 53 A Isat, DCR 0.145 mOhm, 10.0 x 7.0 mm package./p
    • Product Details
    • Download

    FP1010V1-R180-R at a glance: 180 nH high frequency, high current power inductor, 68 A Irms, 53 A Isat, DCR 0.145 mOhm, 10.0 x 7.0 mm body, 10.0 mm tall.

    Eaton FP1010V1-R180-R High frequency, high current power inductors

    Eaton FP1010V1-R180-R is a high frequency, high current power inductor in a 10.0 x 7.0 mm surface-mount package. It carries 180 nH of open-circuit inductance with 68 A Irms and a typical DCR of 0.145 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 10.0 mm tall and rated from -40 °C to +125 °C.

    Key Specifications

    Orderable part numberFP1010V1-R180-R
    Inductance, OCL (0 Adc)180 nH
    Inductance, FLL (minimum)130 nH
    Irms (40 °C rise, no core loss)68 A
    Isat (20% roll-off @ +25 °C)53 A
    Isat2 (20% roll-off @ +75 °C)48 A
    Isat3 (20% roll-off @ +100 °C)46 A
    DCR typical @ +20 °C0.145 mOhm
    K-factor (Bp-p = K x L x dI)352
    Package10.0 x 7.0 mm, 10.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    The Figures Explained

    At zero bias the winding measures 180 nH. Put Isat1 through it and the figure falls to 130 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 180 nH number; loop stability and worst-case current belong on the lower one.

    Saturation is quoted as 20% roll-off at 53 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    The 670 mW dissipated at 68 A through 0.145 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Core loss needs flux, and flux here is about 100.7 mT for a 15.9 A ripple (K = 352). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Series Positioning

    The 10.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 180 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 7 of 11 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.145 mOhm, Irms of 68 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high- power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    The order of checks that works: compute ripple from 180 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.145 mOhm the winding is not the loss, the trace can be.

    Outline Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1010V1-R180-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message