Eaton FP1010V11-R070-R 61 A SMD Power Inductor, 70 nH
Eaton FP1010V11-R070-R 61 A SMD Power Inductor, 70 nH

Eaton FP1010V11-R070-R 61 A SMD Power Inductor, 70 nH

Share
pEaton FP1010V11-R070-R: 70 nH high frequency, high current power inductor, 61 A Irms, A Isat, DCR 0.2 mOhm, 10.0 x 4.5 mm package./p
    • Product Details
    • Download

    FP1010V11-R070-R at a glance: 70 nH high frequency, high current power inductor, 61 A Irms, - A Isat, DCR 0.2 mOhm, 10.0 x 4.5 mm body, 10.0 mm tall.

    Eaton FP1010V11-R070-R High frequency, high current power inductors

    Eaton FP1010V11-R070-R is a high frequency, high current power inductor in a 10.0 x 4.5 mm surface-mount package. It carries 70 nH of open-circuit inductance with 61 A Irms and a typical DCR of 0.2 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 10.0 mm tall and rated from -40 °C to +125 °C.

    Ratings at a Glance

    Orderable part numberFP1010V11-R070-R
    Inductance, OCL (0 Adc)70 nH
    Inductance, FLL (minimum)50 nH
    Irms (40 °C rise, no core loss)61 A
    Isat2 (20% roll-off @ +100 °C)115 A
    Isat3 (20% roll-off @ +125 °C)108 A
    DCR typical @ +20 °C0.2 mOhm
    K-factor (Bp-p = K x L x dI)460
    Package10.0 x 4.5 mm, 10.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    The Figures Explained

    At zero bias the winding measures 70 nH. Put Isat1 through it and the figure falls to 50 nH, about 29% lower, because the ferrite is partly saturated. Ripple calculations belong on the 70 nH number; loop stability and worst-case current belong on the lower one.

    The first Isat column, - A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Copper loss at the rated current works out at about 744 mW (61 A squared times 0.2 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.

    Positioning in the FP Range

    The 10.0 x 4.5 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 70 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    • Application fit: Multi-phase and Vcore regulators, Voltage regulator modules (VRMs) and high power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    The order of checks that works: compute ripple from 70 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.2 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1010V11-R070-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message