Eaton FP1010V14-R070-R 70 nH Power Inductor, 68 A
Eaton FP1010V14-R070-R 70 nH Power Inductor, 68 A

Eaton FP1010V14-R070-R 70 nH Power Inductor, 68 A

Share
pEaton FP1010V14-R070-R: 70 nH high frequency, high current power inductor, 68 A Irms, A Isat, DCR 0.15 mOhm, 9.6 x 6.4 mm package./p
    • Product Details
    • Download

    FP1010V14-R070-R at a glance: 70 nH high frequency, high current power inductor, 68 A Irms, - A Isat, DCR 0.15 mOhm, 9.6 x 6.4 mm body, 10.0 mm tall.

    Eaton FP1010V14-R070-R High frequency, high current power inductors

    Eaton FP1010V14-R070-R is a high frequency, high current power inductor in a 9.6 x 6.4 mm surface-mount package. It carries 70 nH of open-circuit inductance with 68 A Irms and a typical DCR of 0.15 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 10.0 mm tall and rated from -40 °C to +125 °C.

    Electrical Specifications

    Orderable part numberFP1010V14-R070-R
    Inductance, OCL (0 Adc)70 nH
    Inductance, FLL (minimum)55 nH
    Irms (40 °C rise, no core loss)68 A
    Isat2 (20% roll-off @ +100 °C)127 A
    Isat3 (20% roll-off @ +125 °C)120 A
    DCR typical @ +20 °C0.15 mOhm
    K-factor (Bp-p = K x L x dI)339
    Package9.6 x 6.4 mm, 10.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    The Figures Explained

    At zero bias the winding measures 70 nH. Put Isat1 through it and the figure falls to 55 nH, about 21% lower, because the ferrite is partly saturated. Ripple calculations belong on the 70 nH number; loop stability and worst-case current belong on the lower one.

    The first Isat column, - A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Irms of 68 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.15 mOhm that is roughly 694 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.

    Series Positioning

    The 9.6 x 6.4 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 70 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it the lowest inductance of the 3 parts in this data sheet.

    • Application fit: Multi-phase and Vcore regulators, Voltage regulator modules (VRMs) and high power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    The order of checks that works: compute ripple from 70 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.15 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1010V14-R070-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products