
FP1010V14-R090-R at a glance: 90 nH high frequency, high current power inductor, 68 A Irms, 134 A Isat, DCR 0.15 mOhm, 9.6 x 6.4 mm body, 10.0 mm tall.
FP1010V14-R090-R is one of Eaton's high frequency, high current power inductor series, 9.6 x 6.4 mm with a 10.0 mm tall profile. Electrically it offers 90 nH at 68 A Irms and 0.15 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.
| Orderable part number | FP1010V14-R090-R |
| Inductance, OCL (0 Adc) | 90 nH |
| Inductance, FLL (minimum) | 65 nH |
| Irms (40 °C rise, no core loss) | 68 A |
| Isat (20% roll-off @ +25 °C) | 134 A |
| Isat2 (20% roll-off @ +100 °C) | 114 A |
| Isat3 (20% roll-off @ +125 °C) | 107 A |
| DCR typical @ +20 °C | 0.15 mOhm |
| K-factor (Bp-p = K x L x dI) | 339 |
| Package | 9.6 x 6.4 mm, 10.0 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| Moisture sensitivity level | MSL 1 |
| RoHS | Compliant (-R suffix) |
At zero bias the winding measures 90 nH. Put Isat1 through it and the figure falls to 65 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 90 nH number; loop stability and worst-case current belong on the lower one.
Peak current at 20% roll-off is 134 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.
The 694 mW dissipated at 68 A through 0.15 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.
The K-factor of 339 turns ripple into flux: a peak-to-peak swing of 40.2 A gives about 122.7 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.
The 9.6 x 6.4 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 90 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.
That makes it part 2 of 3 when the data sheet is sorted by inductance.
Size the inductor on peak current first, not average. With 90 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.
Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.15 mOhm the winding is not the loss, the trace can be.
The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

What does the R suffix on the part number mean?
It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.
Why is the saturation current listed at several temperatures?
Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd