
FP1010V4-R330-R at a glance: 330 nH high frequency, high current power inductor, 34 A Irms, 35 A Isat, DCR 0.4 mOhm, 10.0 x 7.0 mm body, 10.0 mm tall.
Eaton FP1010V4-R330-R is a high frequency, high current power inductor in a 10.0 x 7.0 mm surface-mount package. It carries 330 nH of open-circuit inductance with 34 A Irms and a typical DCR of 0.4 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 10.0 mm tall and rated from -40 °C to +125 °C.
| Orderable part number | FP1010V4-R330-R |
| Inductance, OCL (0 Adc) | 330 nH |
| Inductance, FLL (minimum) | 230 nH |
| Irms (40 °C rise, no core loss) | 34 A |
| Isat (20% roll-off @ +25 °C) | 35 A |
| Isat2 (20% roll-off @ +75 °C) | 33 A |
| Isat3 (20% roll-off @ +100 °C) | 30 A |
| DCR typical @ +20 °C | 0.4 mOhm |
| K-factor (Bp-p = K x L x dI) | 216 |
| Package | 10.0 x 7.0 mm, 10.0 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| Moisture sensitivity level | MSL 1 |
| RoHS | Compliant (-R suffix) |
At zero bias the winding measures 330 nH. Put Isat1 through it and the figure falls to 230 nH, about 30% lower, because the ferrite is partly saturated. Ripple calculations belong on the 330 nH number; loop stability and worst-case current belong on the lower one.
Peak current at 20% roll-off is 35 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.
Irms of 34 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.4 mOhm that is roughly 462 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.
Core loss needs flux, and flux here is about 74.8 mT for a 10.5 A ripple (K = 216). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.
The 10.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 330 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.
That makes it part 8 of 11 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.4 mOhm, which is what the extra turns cost, Irms of 34 A is the bottom of the family.
Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 330 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.
On the board, place the part so the switch-node copper is short and wide. At 0.4 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

Why is the saturation current listed at several temperatures?
Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.
Why does DCR have both a typical and a maximum figure?
The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd