Eaton FP1010V6-R470-R 470 nH 30 A Saturation Inductor
Eaton FP1010V6-R470-R 470 nH 30 A Saturation Inductor

Eaton FP1010V6-R470-R 470 nH 30 A Saturation Inductor

Share
pEaton FP1010V6-R470-R: 470 nH high frequency, high current power inductor, 54 A Irms, 30 A Isat, DCR 0.4 mOhm, 10.0 x 7.0 mm package./p
    • Product Details
    • Download

    FP1010V6-R470-R at a glance: 470 nH high frequency, high current power inductor, 54 A Irms, 30 A Isat, DCR 0.4 mOhm, 10.0 x 7.0 mm body, 10.0 mm tall.

    Eaton FP1010V6-R470-R High frequency, high current power inductors

    FP1010V6-R470-R is one of Eaton's high frequency, high current power inductor series, 10.0 x 7.0 mm with a 10.0 mm tall profile. Electrically it offers 470 nH at 54 A Irms and 0.4 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Key Specifications

    Orderable part numberFP1010V6-R470-R
    Inductance, OCL (0 Adc)470 nH
    Inductance, FLL (minimum)329 nH
    Irms (40 °C rise, no core loss)54 A
    Isat (20% roll-off @ +25 °C)30 A
    Isat2 (20% roll-off @ +75 °C)22 A
    Isat3 (20% roll-off @ +100 °C)21 A
    DCR typical @ +20 °C0.4 mOhm
    K-factor (Bp-p = K x L x dI)216
    Package10.0 x 7.0 mm, 10.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    At zero bias the winding measures 470 nH. Put Isat1 through it and the figure falls to 329 nH, about 30% lower, because the ferrite is partly saturated. Ripple calculations belong on the 470 nH number; loop stability and worst-case current belong on the lower one.

    Saturation is quoted as 20% roll-off at 30 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Irms of 54 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.4 mOhm that is roughly 1166 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Core loss needs flux, and flux here is about 91.4 mT for a 9 A ripple (K = 216). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    What This Family Is For

    The 10.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 470 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it the highest inductance of the 11 parts in this data sheet, with the highest DCR in the series at 0.4 mOhm, which is what the extra turns cost.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high- power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 470 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.4 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1010V6-R470-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products