Eaton FP1012V2-R070-R 70 nH Power Inductor, 84 A
Eaton FP1012V2-R070-R 70 nH Power Inductor, 84 A

Eaton FP1012V2-R070-R 70 nH Power Inductor, 84 A

Share
pEaton FP1012V2-R070-R: 70 nH high frequency, high current power inductor, 84 A Irms, A Isat, DCR 0.125 mOhm, 10.0 x 6.0 mm package./p
    • Product Details
    • Download

    FP1012V2-R070-R at a glance: 70 nH high frequency, high current power inductor, 84 A Irms, - A Isat, DCR 0.125 mOhm, 10.0 x 6.0 mm body, 12.0 mm tall.

    Eaton FP1012V2-R070-R High frequency, high current power inductors

    Eaton builds the FP1012V2-R070-R as a high frequency, high current power inductor for 10.0 x 6.0 mm footprints. At 70 nH and 84 A Irms with 0.125 mOhm of DCR it targets high-current DC-DC stages; the 12.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Specification Table

    Orderable part numberFP1012V2-R070-R
    Inductance, OCL (0 Adc)70 nH
    Inductance, FLL (minimum)50 nH
    Irms (40 °C rise, no core loss)84 A
    DCR typical @ +20 °C0.125 mOhm
    K-factor (Bp-p = K x L x dI)305
    Package10.0 x 6.0 mm, 12.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    At zero bias the winding measures 70 nH. Put Isat1 through it and the figure falls to 50 nH, about 29% lower, because the ferrite is partly saturated. Ripple calculations belong on the 70 nH number; loop stability and worst-case current belong on the lower one.

    Peak current at 20% roll-off is - A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Copper loss at the rated current works out at about 882 mW (84 A squared times 0.125 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.

    What This Family Is For

    The 10.0 x 6.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 70 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it the lowest inductance of the 16 parts in this data sheet.

    • Application fit: Multi-phase and Vcore regulators, Voltage regulator modules (VRMs) and high power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Size the inductor on peak current first, not average. With 70 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    On the board, place the part so the switch-node copper is short and wide. At 0.125 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Outline Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1012V2-R070-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message