Eaton FP1012V3-R070-R 84 A SMD Power Inductor, 70 nH
Eaton FP1012V3-R070-R 84 A SMD Power Inductor, 70 nH

Eaton FP1012V3-R070-R 84 A SMD Power Inductor, 70 nH

Share
pEaton FP1012V3-R070-R: 70 nH high frequency, high current power inductor, 84 A Irms, 190 A Isat, DCR 0.125 mOhm, 10.0 x 6.0 mm package./p
    • Product Details
    • Download

    FP1012V3-R070-R at a glance: 70 nH high frequency, high current power inductor, 84 A Irms, 190 A Isat, DCR 0.125 mOhm, 10.0 x 6.0 mm body, 12.0 mm tall.

    Eaton FP1012V3-R070-R High frequency, high current power inductors

    The FP1012V3-R070-R is a 10.0 x 6.0 mm high frequency, high current power inductor from Eaton, rated 84 A Irms at 70 nH and 0.125 mOhm typical DCR. It is a surface-mount part 12.0 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Electrical Specifications

    Orderable part numberFP1012V3-R070-R
    Inductance, OCL (0 Adc)70 nH
    Inductance, FLL (minimum)50 nH
    Irms (40 °C rise, no core loss)84 A
    Isat (20% roll-off @ +25 °C)190 A
    Isat2 (20% roll-off @ +100 °C)172 A
    Isat3 (20% roll-off @ +125 °C)160 A
    DCR typical @ +20 °C0.125 mOhm
    K-factor (Bp-p = K x L x dI)305
    Package10.0 x 6.0 mm, 12.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Two inductance figures are published. 70 nH is measured with no DC in the winding, 50 nH with the winding loaded to Isat1. The gap between them is 29%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Saturation is quoted as 20% roll-off at 190 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    The 882 mW dissipated at 84 A through 0.125 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Core loss needs flux, and flux here is about 121.7 mT for a 57 A ripple (K = 305). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Where This Part Sits in the Range

    The 10.0 x 6.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 70 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it the lowest inductance of the 16 parts in this data sheet.

    • Application fit: Multi-phase and Vcore regulators, Voltage regulator modules (VRMs) and high power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 70 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.125 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1012V3-R070-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message