Eaton FP1105R1-R22-R 226 nH Power Inductor, 46 A
Eaton FP1105R1-R22-R 226 nH Power Inductor, 46 A

Eaton FP1105R1-R22-R 226 nH Power Inductor, 46 A

Share
pEaton FP1105R1-R22-R: 226 nH high current power inductor, 46 A Irms, 39 A Isat, DCR 0.35 mOhm, 11.0 x 8.0 mm package./p
    • Product Details
    • Download

    FP1105R1-R22-R at a glance: 226 nH high current power inductor, 46 A Irms, 39 A Isat, DCR 0.35 mOhm, 11.0 x 8.0 mm body, 4.9 mm tall.

    Eaton FP1105R1-R22-R High current power inductors

    FP1105R1-R22-R is one of Eaton's high current power inductor series, 11.0 x 8.0 mm with a 4.9 mm tall profile. Electrically it offers 226 nH at 46 A Irms and 0.35 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Electrical Specifications

    Orderable part numberFP1105R1-R22-R
    Inductance, OCL (0 Adc)226 nH
    Inductance, FLL (minimum)163 nH
    Irms (40 °C rise, no core loss)46 A
    Isat (20% roll-off @ +25 °C)39 A
    Isat2 (20% roll-off @ +125 °C)28 A
    DCR typical @ +20 °C0.35 mOhm
    K-factor (Bp-p = K x L x dI)467
    Package11.0 x 8.0 mm, 4.9 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    At zero bias the winding measures 226 nH. Put Isat1 through it and the figure falls to 163 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 226 nH number; loop stability and worst-case current belong on the lower one.

    The first Isat column, 39 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Copper loss at the rated current works out at about 741 mW (46 A squared times 0.35 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The K-factor of 467 turns ripple into flux: a peak-to-peak swing of 11.7 A gives about 123.5 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Where This Part Sits in the Range

    The 11.0 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 226 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it the highest inductance of the 5 parts in this data sheet.

    • Application fit: Multi-phase regulators, Voltage Regulator Module (VRM), Portable electronics.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Size the inductor on peak current first, not average. With 226 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.35 mOhm the winding is not the loss, the trace can be.

    Outline Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1105R1-R22-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products