Eaton FP1107R2-R07-R 42 A SMD Power Inductor, 70 nH
Eaton FP1107R2-R07-R 42 A SMD Power Inductor, 70 nH

Eaton FP1107R2-R07-R 42 A SMD Power Inductor, 70 nH

Share
pEaton FP1107R2-R07-R: 70 nH high frequency, high current power inductor, 42 A Irms, 140 A Isat, DCR 0.47 mOhm, 11.2 x 8.0 mm package./p
    • Product Details
    • Download

    FP1107R2-R07-R at a glance: 70 nH high frequency, high current power inductor, 42 A Irms, 140 A Isat, DCR 0.47 mOhm, 11.2 x 8.0 mm body, 7.5 mm tall.

    Eaton FP1107R2-R07-R High frequency, high current power inductors

    The FP1107R2-R07-R is a 11.2 x 8.0 mm high frequency, high current power inductor from Eaton, rated 42 A Irms at 70 nH and 0.47 mOhm typical DCR. It is a surface-mount part 7.5 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Key Specifications

    Orderable part numberFP1107R2-R07-R
    Inductance, OCL (0 Adc)70 nH
    Inductance, FLL (minimum)50 nH
    Irms (40 °C rise, no core loss)42 A
    Isat (20% roll-off @ +25 °C)140 A
    Isat4 (20% roll-off @ +125 °C)123 A
    DCR typical @ +20 °C0.47 mOhm
    K-factor (Bp-p = K x L x dI)363.3
    Package11.2 x 8.0 mm, 7.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    The Figures Explained

    At zero bias the winding measures 70 nH. Put Isat1 through it and the figure falls to 50 nH, about 29% lower, because the ferrite is partly saturated. Ripple calculations belong on the 70 nH number; loop stability and worst-case current belong on the lower one.

    The first Isat column, 140 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Copper loss at the rated current works out at about 829 mW (42 A squared times 0.47 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Flux swing follows Bp-p = K x L x dI. With K = 363.3 and a ripple of 42 A the core sees roughly 106.8 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Positioning in the FP Range

    The 11.2 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 70 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it the lowest inductance of the 22 parts in this data sheet, with the highest DCR in the series at 0.47 mOhm, which is what the extra turns cost, Irms of 42 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 70 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.47 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1107R2-R07-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message