Eaton FP1107R2-R40-R 42 A SMD Power Inductor, 400 nH
Eaton FP1107R2-R40-R 42 A SMD Power Inductor, 400 nH

Eaton FP1107R2-R40-R 42 A SMD Power Inductor, 400 nH

Share
pEaton FP1107R2-R40-R: 400 nH high frequency, high current power inductor, 42 A Irms, 25 A Isat, DCR 0.47 mOhm, 11.2 x 8.0 mm package./p
    • Product Details
    • Download

    FP1107R2-R40-R at a glance: 400 nH high frequency, high current power inductor, 42 A Irms, 25 A Isat, DCR 0.47 mOhm, 11.2 x 8.0 mm body, 7.5 mm tall.

    Eaton FP1107R2-R40-R High frequency, high current power inductors

    Eaton builds the FP1107R2-R40-R as a high frequency, high current power inductor for 11.2 x 8.0 mm footprints. At 400 nH and 42 A Irms with 0.47 mOhm of DCR it targets high-current DC-DC stages; the 7.5 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Specification Table

    Orderable part numberFP1107R2-R40-R
    Inductance, OCL (0 Adc)400 nH
    Inductance, FLL (minimum)288 nH
    Irms (40 °C rise, no core loss)42 A
    Isat (20% roll-off @ +25 °C)25 A
    Isat4 (20% roll-off @ +125 °C)20 A
    DCR typical @ +20 °C0.47 mOhm
    K-factor (Bp-p = K x L x dI)363.3
    Package11.2 x 8.0 mm, 7.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    400 nH open-circuit, 288 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    The first Isat column, 25 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    The 829 mW dissipated at 42 A through 0.47 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The K-factor of 363.3 turns ripple into flux: a peak-to-peak swing of 7.5 A gives about 109 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    What This Family Is For

    The 11.2 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 400 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 17 of 22 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.47 mOhm, which is what the extra turns cost, Irms of 42 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    Size the inductor on peak current first, not average. With 400 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.47 mOhm the winding is not the loss, the trace can be.

    Outline Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1107R2-R40-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products