Eaton FP1108L1-R180-R - 180 nH Shielded Power Inductor 11.0 x 8.2 mm
Eaton FP1108L1-R180-R - 180 nH Shielded Power Inductor 11.0 x 8.2 mm

Eaton FP1108L1-R180-R - 180 nH Shielded Power Inductor 11.0 x 8.2 mm

Share
pEaton FP1108L1-R180-R: 180 nH high frequency, high current power inductor, 64 A Irms, 47 A Isat, DCR 0.1 mOhm, 11.0 x 8.2 mm package./p
    • Product Details
    • Download

    FP1108L1-R180-R at a glance: 180 nH high frequency, high current power inductor, 64 A Irms, 47 A Isat, DCR 0.1 mOhm, 11.0 x 8.2 mm body, 8.3 mm tall.

    Eaton FP1108L1-R180-R High frequency, high current power inductors

    Eaton FP1108L1-R180-R is a high frequency, high current power inductor in a 11.0 x 8.2 mm surface-mount package. It carries 180 nH of open-circuit inductance with 64 A Irms and a typical DCR of 0.1 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 8.3 mm tall and rated from -40 °C to +125 °C.

    Key Specifications

    Orderable part numberFP1108L1-R180-R
    Inductance, OCL (0 Adc)180 nH
    Inductance, FLL (minimum)129 nH
    Irms (40 °C rise, no core loss)64 A
    Isat (20% roll-off @ +25 °C)47 A
    Isat2 (20% roll-off @ +75 °C)41 A
    Isat3 (20% roll-off @ +100 °C)37 A
    DCR typical @ +20 °C0.1 mOhm
    K-factor (Bp-p = K x L x dI)422
    Package11.0 x 8.2 mm, 8.3 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    Two inductance figures are published. 180 nH is measured with no DC in the winding, 129 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Peak current at 20% roll-off is 47 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 410 mW dissipated at 64 A through 0.1 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The K-factor of 422 turns ripple into flux: a peak-to-peak swing of 14.1 A gives about 107.1 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    What This Family Is For

    The 11.0 x 8.2 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 180 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it the highest inductance of the 4 parts in this data sheet, and it shares the lowest DCR here at 0.1 mOhm, Irms of 64 A is the top of the family.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 180 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.1 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1108L1-R180-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products