
FP1108L2-R150-R at a glance: 150 nH high frequency, high current power inductor, 48 A Irms, 55 A Isat, DCR 0.18 mOhm, 11.0 x 8.2 mm body, 8.3 mm tall.
FP1108L2-R150-R is one of Eaton's high frequency, high current power inductor series, 11.0 x 8.2 mm with a 8.3 mm tall profile. Electrically it offers 150 nH at 48 A Irms and 0.18 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.
| Orderable part number | FP1108L2-R150-R |
| Inductance, OCL (0 Adc) | 150 nH |
| Inductance, FLL (minimum) | 108 nH |
| Irms (40 °C rise, no core loss) | 48 A |
| Isat (20% roll-off @ +25 °C) | 55 A |
| Isat2 (20% roll-off @ +75 °C) | 50 A |
| Isat3 (20% roll-off @ +100 °C) | 46 A |
| DCR typical @ +20 °C | 0.18 mOhm |
| K-factor (Bp-p = K x L x dI) | 390 |
| Package | 11.0 x 8.2 mm, 8.3 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
150 nH open-circuit, 108 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.
Peak current at 20% roll-off is 55 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.
The 415 mW dissipated at 48 A through 0.18 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.
Flux swing follows Bp-p = K x L x dI. With K = 390 and a ripple of 16.5 A the core sees roughly 96.5 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.
The 11.0 x 8.2 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 150 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.
That makes it part 2 of 4 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.18 mOhm, which is what the extra turns cost, Irms of 48 A is the bottom of the family.
The order of checks that works: compute ripple from 150 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.
On the board, place the part so the switch-node copper is short and wide. At 0.18 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.
The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

What does the R suffix on the part number mean?
It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.
Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd