Eaton FP1108L4-R150-R 150 nH Power Inductor, 91 A
Eaton FP1108L4-R150-R 150 nH Power Inductor, 91 A

Eaton FP1108L4-R150-R 150 nH Power Inductor, 91 A

Share
Eaton FP1108L4-R150-R: 150 nH high frequency, high current power inductor, 91 A Irms, 40 A Isat, DCR 0.05 mOhm, 11.0 x 8.0 mm package.
    • Product Details
    • Download

    FP1108L4-R150-R at a glance: 150 nH high frequency, high current power inductor, 91 A Irms, 40 A Isat, DCR 0.05 mOhm, 11.0 x 8.0 mm body, 8.0 mm tall.

    Eaton FP1108L4-R150-R High frequency, high current power inductors

    FP1108L4-R150-R is one of Eaton's high frequency, high current power inductor series, 11.0 x 8.0 mm with a 8.0 mm tall profile. Electrically it offers 150 nH at 91 A Irms and 0.05 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Electrical Specifications

    Orderable part numberFP1108L4-R150-R
    Inductance, OCL (0 Adc)150 nH
    Inductance, FLL (minimum)108 nH
    Irms (40 °C rise, no core loss)91 A
    Isat (20% roll-off @ +25 °C)40 A
    Isat2 (20% roll-off @ +100 °C)34 A
    Isat3 (20% roll-off @ +125 °C)32 A
    DCR typical @ +20 °C0.05 mOhm
    K-factor (Bp-p = K x L x dI)552
    Package11.0 x 8.0 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    Two inductance figures are published. 150 nH is measured with no DC in the winding, 108 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Saturation is quoted as 20% roll-off at 40 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Irms of 91 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.05 mOhm that is roughly 414 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Flux swing follows Bp-p = K x L x dI. With K = 552 and a ripple of 12 A the core sees roughly 99.4 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Where This Part Sits in the Range

    The 11.0 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 150 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 3 of 4 when the data sheet is sorted by inductance.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    The order of checks that works: compute ripple from 150 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.05 mOhm the winding is not the loss, the trace can be.

    Mechanical Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1108L4-R150-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message