Eaton FP1109-1R0-R - 950 nH Shielded Power Inductor 11.0 x 9.0 mm
Eaton FP1109-1R0-R - 950 nH Shielded Power Inductor 11.0 x 9.0 mm

Eaton FP1109-1R0-R - 950 nH Shielded Power Inductor 11.0 x 9.0 mm

Share
pEaton FP1109-1R0-R: 950 nH high frequency, high current power inductor, 35 A Irms, 11.5 A Isat, DCR 0.42 mOhm, 11.0 x 9.0 mm package./p
    • Product Details
    • Download

    FP1109-1R0-R at a glance: 950 nH high frequency, high current power inductor, 35 A Irms, 11.5 A Isat, DCR 0.42 mOhm, 11.0 x 9.0 mm body, 9.0 mm tall.

    Eaton FP1109-1R0-R High frequency, high current power inductors

    Eaton builds the FP1109-1R0-R as a high frequency, high current power inductor for 11.0 x 9.0 mm footprints. At 950 nH and 35 A Irms with 0.42 mOhm of DCR it targets high-current DC-DC stages; the 9.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Electrical Specifications

    Orderable part numberFP1109-1R0-R
    Inductance, OCL (0 Adc)950 nH
    Inductance, FLL (minimum)565 nH
    Irms (40 °C rise, no core loss)35 A
    Isat (30% roll-off @ +25 °C)11.5 A
    Isat2 (30% roll-off @ +125 °C)8.5 A
    DCR typical @ +20 °C0.42 mOhm
    K-factor (Bp-p = K x L x dI)233
    Package11.0 x 9.0 mm, 9.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    Two inductance figures are published. 950 nH is measured with no DC in the winding, 565 nH with the winding loaded to Isat1. The gap between them is 41%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Saturation is quoted as 30% roll-off at 11.5 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Irms of 35 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.42 mOhm that is roughly 514 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Flux swing follows Bp-p = K x L x dI. With K = 233 and a ripple of 3.45 A the core sees roughly 76.4 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Positioning in the FP Range

    The 11.0 x 9.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 950 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it the highest inductance of the 7 parts in this data sheet.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Size the inductor on peak current first, not average. With 950 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    On the board, place the part so the switch-node copper is short and wide. At 0.42 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1109-1R0-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message