Eaton FP1109-R23-R 35 A SMD Power Inductor, 247 nH
Eaton FP1109-R23-R 35 A SMD Power Inductor, 247 nH

Eaton FP1109-R23-R 35 A SMD Power Inductor, 247 nH

Share
pEaton FP1109-R23-R: 247 nH high frequency, high current power inductor, 35 A Irms, 55 A Isat, DCR 0.42 mOhm, 11.0 x 9.0 mm package./p
    • Product Details
    • Download

    FP1109-R23-R at a glance: 247 nH high frequency, high current power inductor, 35 A Irms, 55 A Isat, DCR 0.42 mOhm, 11.0 x 9.0 mm body, 9.0 mm tall.

    Eaton FP1109-R23-R High frequency, high current power inductors

    Eaton builds the FP1109-R23-R as a high frequency, high current power inductor for 11.0 x 9.0 mm footprints. At 247 nH and 35 A Irms with 0.42 mOhm of DCR it targets high-current DC-DC stages; the 9.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Specification Table

    Orderable part numberFP1109-R23-R
    Inductance, OCL (0 Adc)247 nH
    Inductance, FLL (minimum)147 nH
    Irms (40 °C rise, no core loss)35 A
    Isat (30% roll-off @ +25 °C)55 A
    Isat2 (30% roll-off @ +125 °C)41 A
    DCR typical @ +20 °C0.42 mOhm
    K-factor (Bp-p = K x L x dI)233
    Package11.0 x 9.0 mm, 9.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    At zero bias the winding measures 247 nH. Put Isat1 through it and the figure falls to 147 nH, about 40% lower, because the ferrite is partly saturated. Ripple calculations belong on the 247 nH number; loop stability and worst-case current belong on the lower one.

    Peak current at 30% roll-off is 55 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Copper loss at the rated current works out at about 514 mW (35 A squared times 0.42 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Core loss needs flux, and flux here is about 95 mT for a 16.5 A ripple (K = 233). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    What This Family Is For

    The 11.0 x 9.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 247 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 2 of 7 when the data sheet is sorted by inductance.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 247 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.42 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1109-R23-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products