Eaton FP1109-R33-R 311 nH Power Inductor, 35 A
Eaton FP1109-R33-R 311 nH Power Inductor, 35 A

Eaton FP1109-R33-R 311 nH Power Inductor, 35 A

Share
pEaton FP1109-R33-R: 311 nH high frequency, high current power inductor, 35 A Irms, 44 A Isat, DCR 0.42 mOhm, 11.0 x 9.0 mm package./p
    • Product Details
    • Download

    FP1109-R33-R at a glance: 311 nH high frequency, high current power inductor, 35 A Irms, 44 A Isat, DCR 0.42 mOhm, 11.0 x 9.0 mm body, 9.0 mm tall.

    Eaton FP1109-R33-R High frequency, high current power inductors

    Eaton builds the FP1109-R33-R as a high frequency, high current power inductor for 11.0 x 9.0 mm footprints. At 311 nH and 35 A Irms with 0.42 mOhm of DCR it targets high-current DC-DC stages; the 9.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Electrical Specifications

    Orderable part numberFP1109-R33-R
    Inductance, OCL (0 Adc)311 nH
    Inductance, FLL (minimum)185 nH
    Irms (40 °C rise, no core loss)35 A
    Isat (30% roll-off @ +25 °C)44 A
    Isat2 (30% roll-off @ +125 °C)33 A
    DCR typical @ +20 °C0.42 mOhm
    K-factor (Bp-p = K x L x dI)233
    Package11.0 x 9.0 mm, 9.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    311 nH open-circuit, 185 nH at full load: that is a 41% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Peak current at 30% roll-off is 44 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Irms of 35 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.42 mOhm that is roughly 514 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Core loss needs flux, and flux here is about 95.7 mT for a 13.2 A ripple (K = 233). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Positioning in the FP Range

    The 11.0 x 9.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 311 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 4 of 7 when the data sheet is sorted by inductance.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    The order of checks that works: compute ripple from 311 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.42 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1109-R33-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products