Eaton FP1109B1-R180-R 180 nH 62 A Saturation Inductor
Eaton FP1109B1-R180-R 180 nH 62 A Saturation Inductor

Eaton FP1109B1-R180-R 180 nH 62 A Saturation Inductor

Share
pEaton FP1109B1-R180-R: 180 nH high frequency, high current power inductor, 55 A Irms, 62 A Isat, DCR 0.19 mOhm, 11.0 x 8.2 mm package./p
    • Product Details
    • Download

    FP1109B1-R180-R at a glance: 180 nH high frequency, high current power inductor, 55 A Irms, 62 A Isat, DCR 0.19 mOhm, 11.0 x 8.2 mm body, 9.0 mm tall.

    Eaton FP1109B1-R180-R High frequency, high current power inductors

    Eaton builds the FP1109B1-R180-R as a high frequency, high current power inductor for 11.0 x 8.2 mm footprints. At 180 nH and 55 A Irms with 0.19 mOhm of DCR it targets high-current DC-DC stages; the 9.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Specification Table

    Orderable part numberFP1109B1-R180-R
    Inductance, OCL (0 Adc)180 nH
    Inductance, FLL (minimum)130 nH
    Irms (40 °C rise, no core loss)55 A
    Isat (20% roll-off @ +25 °C)62 A
    Isat2 (20% roll-off @ +125 °C)49 A
    DCR typical @ +20 °C0.19 mOhm
    K-factor (Bp-p = K x L x dI)339
    Package11.0 x 8.2 mm, 9.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    At zero bias the winding measures 180 nH. Put Isat1 through it and the figure falls to 130 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 180 nH number; loop stability and worst-case current belong on the lower one.

    The first Isat column, 62 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Irms of 55 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.19 mOhm that is roughly 575 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Core loss needs flux, and flux here is about 113.5 mT for a 18.6 A ripple (K = 339). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Positioning in the FP Range

    The 11.0 x 8.2 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 180 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 2 of 4 when the data sheet is sorted by inductance.

    • Application fit: Compatible with Infineon® DrBlade™ digital voltage regulator controller, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Size the inductor on peak current first, not average. With 180 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.19 mOhm the winding is not the loss, the trace can be.

    Outline Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1109B1-R180-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products