Eaton FP1110V1-R27-R 270 nH Power Inductor, 61 A
Eaton FP1110V1-R27-R 270 nH Power Inductor, 61 A

Eaton FP1110V1-R27-R 270 nH Power Inductor, 61 A

Share
pEaton FP1110V1-R27-R: 270 nH high frequency, high current power inductor, 61 A Irms, 55 A Isat, DCR 0.23 mOhm, 11.0 x 10.0 mm package./p
    • Product Details
    • Download

    FP1110V1-R27-R at a glance: 270 nH high frequency, high current power inductor, 61 A Irms, 55 A Isat, DCR 0.23 mOhm, 11.0 x 10.0 mm body, 9.5 mm tall.

    Eaton FP1110V1-R27-R High frequency, high current power inductors

    The FP1110V1-R27-R is a 11.0 x 10.0 mm high frequency, high current power inductor from Eaton, rated 61 A Irms at 270 nH and 0.23 mOhm typical DCR. It is a surface-mount part 9.5 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Electrical Specifications

    Orderable part numberFP1110V1-R27-R
    Inductance, OCL (0 Adc)270 nH
    Inductance, FLL (minimum)173 nH
    Irms (40 °C rise, no core loss)61 A
    Isat (20% roll-off @ +100 °C)55 A
    Isat2 (20% roll-off @ +100 °C)44 A
    DCR typical @ +20 °C0.23 mOhm
    K-factor (Bp-p = K x L x dI)278
    Package11.0 x 10.0 mm, 9.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    Two inductance figures are published. 270 nH is measured with no DC in the winding, 173 nH with the winding loaded to Isat1. The gap between them is 36%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Saturation is quoted as 20% roll-off at 55 A at +100 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Irms of 61 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.23 mOhm that is roughly 856 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Core loss needs flux, and flux here is about 123.8 mT for a 16.5 A ripple (K = 278). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Positioning in the FP Range

    The 11.0 x 10.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 270 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 8 of 11 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.23 mOhm, which is what the extra turns cost.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    The order of checks that works: compute ripple from 270 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.23 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Outline Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1110V1-R27-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products