Eaton FP1110V2-R270-R - 270 nH Shielded Power Inductor 11.0 x 10.0 mm
Eaton FP1110V2-R270-R - 270 nH Shielded Power Inductor 11.0 x 10.0 mm

Eaton FP1110V2-R270-R - 270 nH Shielded Power Inductor 11.0 x 10.0 mm

Share
pEaton FP1110V2-R270-R: 270 nH high frequency, high current power inductor, 61 A Irms, 48 A Isat, DCR 0.18 mOhm, 11.0 x 10.0 mm package./p
    • Product Details
    • Download

    FP1110V2-R270-R at a glance: 270 nH high frequency, high current power inductor, 61 A Irms, 48 A Isat, DCR 0.18 mOhm, 11.0 x 10.0 mm body, 9.5 mm tall.

    Eaton FP1110V2-R270-R High frequency, high current power inductors

    Eaton FP1110V2-R270-R is a high frequency, high current power inductor in a 11.0 x 10.0 mm surface-mount package. It carries 270 nH of open-circuit inductance with 61 A Irms and a typical DCR of 0.18 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 9.5 mm tall and rated from -40 °C to +125 °C.

    Specification Table

    Orderable part numberFP1110V2-R270-R
    Inductance, OCL (0 Adc)270 nH
    Inductance, FLL (minimum)195 nH
    Irms (40 °C rise, no core loss)61 A
    Isat (20% roll-off @ +100 °C)48 A
    Isat2 (20% roll-off @ +100 °C)38.5 A
    DCR typical @ +20 °C0.18 mOhm
    K-factor (Bp-p = K x L x dI)328
    Package11.0 x 10.0 mm, 9.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    270 nH open-circuit, 195 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Peak current at 20% roll-off is 48 A at +100 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 670 mW dissipated at 61 A through 0.18 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The K-factor of 328 turns ripple into flux: a peak-to-peak swing of 14.4 A gives about 127.5 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Where This Part Sits in the Range

    The 11.0 x 10.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 270 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 8 of 11 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.18 mOhm.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 270 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.18 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1110V2-R270-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products