Eaton FP1208R1-R21-R 210 nH Power Inductor, 50 A
Eaton FP1208R1-R21-R 210 nH Power Inductor, 50 A

Eaton FP1208R1-R21-R 210 nH Power Inductor, 50 A

Share
pEaton FP1208R1-R21-R: 210 nH high frequency, high current power inductor, 50 A Irms, 65 A Isat, DCR 0.29 mOhm, 12.0 x 8.0 mm package./p
    • Product Details
    • Download

    FP1208R1-R21-R at a glance: 210 nH high frequency, high current power inductor, 50 A Irms, 65 A Isat, DCR 0.29 mOhm, 12.0 x 8.0 mm body, 8.0 mm tall.

    Eaton FP1208R1-R21-R High frequency, high current power inductors

    Eaton builds the FP1208R1-R21-R as a high frequency, high current power inductor for 12.0 x 8.0 mm footprints. At 210 nH and 50 A Irms with 0.29 mOhm of DCR it targets high-current DC-DC stages; the 8.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Ratings at a Glance

    Orderable part numberFP1208R1-R21-R
    Inductance, OCL (0 Adc)210 nH
    Inductance, FLL (minimum)160 nH
    Irms (40 °C rise, no core loss)50 A
    Isat (20% roll-off @ +25 °C)65 A
    Isat2 (20% roll-off @ +85 °C)57 A
    Isat3 (20% roll-off @ +125 °C)55 A
    DCR typical @ +20 °C0.29 mOhm
    K-factor (Bp-p = K x L x dI)283
    Package12.0 x 8.0 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    Two inductance figures are published. 210 nH is measured with no DC in the winding, 160 nH with the winding loaded to Isat1. The gap between them is 24%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Saturation is quoted as 20% roll-off at 65 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Irms of 50 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.29 mOhm that is roughly 725 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    The K-factor of 283 turns ripple into flux: a peak-to-peak swing of 19.5 A gives about 115.9 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Series Positioning

    At 12.0 x 8.0 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 210 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 3 of 5 when the data sheet is sorted by inductance.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 210 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.29 mOhm the winding is not the loss, the trace can be.

    Outline Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1208R1-R21-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products