Eaton FP1308-R11-R 68 A SMD Power Inductor, 110 nH
Eaton FP1308-R11-R 68 A SMD Power Inductor, 110 nH

Eaton FP1308-R11-R 68 A SMD Power Inductor, 110 nH

Share
pEaton FP1308-R11-R: 110 nH high frequency, high current power inductor, 68 A Irms, 120 A Isat, DCR 0.2 mOhm, 13.7 x 12.9 mm package./p
    • Product Details
    • Download

    FP1308-R11-R at a glance: 110 nH high frequency, high current power inductor, 68 A Irms, 120 A Isat, DCR 0.2 mOhm, 13.7 x 12.9 mm body, 8.0 mm tall.

    Eaton FP1308-R11-R High frequency, high current power inductors

    The FP1308-R11-R is a 13.7 x 12.9 mm high frequency, high current power inductor from Eaton, rated 68 A Irms at 110 nH and 0.2 mOhm typical DCR. It is a surface-mount part 8.0 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Specification Table

    Orderable part numberFP1308-R11-R
    Inductance, OCL (0 Adc)110 nH
    Irms (40 °C rise, no core loss)68 A
    Isat (20% roll-off @ +25 °C)120 A
    DCR typical @ +20 °C0.2 mOhm
    DCR maximum @ +20 °C0.24 mOhm
    K-factor (Bp-p = K x L x dI)21.3
    Package13.7 x 12.9 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    110 nH is the unbiased inductance. The data sheet does not publish a separate full-load figure for this part, so leave margin when you compute ripple at rated current.

    Peak current at 20% roll-off is 120 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Irms of 68 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.2 mOhm that is roughly 925 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    The K-factor of 21.3 turns ripple into flux: a peak-to-peak swing of 36 A gives about 8.4 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Positioning in the FP Range

    At 13.7 x 12.9 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 110 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it the lowest inductance of the 5 parts in this data sheet.

    • Application fit: Voltage regulator modules (VRMs) for servers and microprocessors, Multi-phase buck inductors, High frequency, high current switching power supplies.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 110 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.2 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1308-R11-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products