Eaton FP1308-R26-R 260 nH Power Inductor, 68 A
Eaton FP1308-R26-R 260 nH Power Inductor, 68 A

Eaton FP1308-R26-R 260 nH Power Inductor, 68 A

Share
pEaton FP1308-R26-R: 260 nH high frequency, high current power inductor, 68 A Irms, 60 A Isat, DCR 0.2 mOhm, 13.7 x 12.9 mm package./p
    • Product Details
    • Download

    FP1308-R26-R at a glance: 260 nH high frequency, high current power inductor, 68 A Irms, 60 A Isat, DCR 0.2 mOhm, 13.7 x 12.9 mm body, 8.0 mm tall.

    Eaton FP1308-R26-R High frequency, high current power inductors

    Eaton FP1308-R26-R is a high frequency, high current power inductor in a 13.7 x 12.9 mm surface-mount package. It carries 260 nH of open-circuit inductance with 68 A Irms and a typical DCR of 0.2 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 8.0 mm tall and rated from -40 °C to +125 °C.

    Electrical Specifications

    Orderable part numberFP1308-R26-R
    Inductance, OCL (0 Adc)260 nH
    Irms (40 °C rise, no core loss)68 A
    Isat (20% roll-off @ +25 °C)60 A
    DCR typical @ +20 °C0.2 mOhm
    DCR maximum @ +20 °C0.24 mOhm
    K-factor (Bp-p = K x L x dI)21.3
    Package13.7 x 12.9 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    260 nH is the unbiased inductance. The data sheet does not publish a separate full-load figure for this part, so leave margin when you compute ripple at rated current.

    Saturation is quoted as 20% roll-off at 60 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Irms of 68 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.2 mOhm that is roughly 925 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Flux swing follows Bp-p = K x L x dI. With K = 21.3 and a ripple of 18 A the core sees roughly 10 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    What This Family Is For

    At 13.7 x 12.9 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 260 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 3 of 5 when the data sheet is sorted by inductance.

    • Application fit: Voltage regulator modules (VRMs) for servers and microprocessors, Multi-phase buck inductors, High frequency, high current switching power supplies.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 260 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.2 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1308-R26-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products