Eaton FP1308-R32-R - 320 nH Shielded Power Inductor 13.7 x 12.9 mm
Eaton FP1308-R32-R - 320 nH Shielded Power Inductor 13.7 x 12.9 mm

Eaton FP1308-R32-R - 320 nH Shielded Power Inductor 13.7 x 12.9 mm

Share
pEaton FP1308-R32-R: 320 nH high frequency, high current power inductor, 68 A Irms, 45 A Isat, DCR 0.2 mOhm, 13.7 x 12.9 mm package./p
    • Product Details
    • Download

    FP1308-R32-R at a glance: 320 nH high frequency, high current power inductor, 68 A Irms, 45 A Isat, DCR 0.2 mOhm, 13.7 x 12.9 mm body, 8.0 mm tall.

    Eaton FP1308-R32-R High frequency, high current power inductors

    FP1308-R32-R is one of Eaton's high frequency, high current power inductor series, 13.7 x 12.9 mm with a 8.0 mm tall profile. Electrically it offers 320 nH at 68 A Irms and 0.2 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Specification Table

    Orderable part numberFP1308-R32-R
    Inductance, OCL (0 Adc)320 nH
    Irms (40 °C rise, no core loss)68 A
    Isat (20% roll-off @ +25 °C)45 A
    DCR typical @ +20 °C0.2 mOhm
    DCR maximum @ +20 °C0.24 mOhm
    K-factor (Bp-p = K x L x dI)21.3
    Package13.7 x 12.9 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    320 nH is the unbiased inductance. The data sheet does not publish a separate full-load figure for this part, so leave margin when you compute ripple at rated current.

    The first Isat column, 45 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Copper loss at the rated current works out at about 925 mW (68 A squared times 0.2 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Flux swing follows Bp-p = K x L x dI. With K = 21.3 and a ripple of 13.5 A the core sees roughly 9.2 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    What This Family Is For

    At 13.7 x 12.9 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 320 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 4 of 5 when the data sheet is sorted by inductance.

    • Application fit: Voltage regulator modules (VRMs) for servers and microprocessors, Multi-phase buck inductors, High frequency, high current switching power supplies.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 320 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.2 mOhm the winding is not the loss, the trace can be.

    Mechanical Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1308-R32-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products