Eaton FP1308R1-R11-R 57 A SMD Power Inductor, 110 nH
Eaton FP1308R1-R11-R 57 A SMD Power Inductor, 110 nH

Eaton FP1308R1-R11-R 57 A SMD Power Inductor, 110 nH

Share
pEaton FP1308R1-R11-R: 110 nH high frequency, high current power inductor, 57 A Irms, 120 A Isat, DCR 0.32 mOhm, 13.4 x 12.7 mm package./p
    • Product Details
    • Download

    FP1308R1-R11-R at a glance: 110 nH high frequency, high current power inductor, 57 A Irms, 120 A Isat, DCR 0.32 mOhm, 13.4 x 12.7 mm body, 8.0 mm tall.

    Eaton FP1308R1-R11-R High frequency, high current power inductors

    Eaton builds the FP1308R1-R11-R as a high frequency, high current power inductor for 13.4 x 12.7 mm footprints. At 110 nH and 57 A Irms with 0.32 mOhm of DCR it targets high-current DC-DC stages; the 8.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Key Specifications

    Orderable part numberFP1308R1-R11-R
    Inductance, OCL (0 Adc)110 nH
    Inductance, FLL (minimum)79 nH
    Irms (40 °C rise, no core loss)57 A
    Isat (20% roll-off @ +25 °C)120 A
    Isat2 (20% roll-off @ +125 °C)105 A
    DCR typical @ +20 °C0.32 mOhm
    K-factor (Bp-p = K x L x dI)233
    Package13.4 x 12.7 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    110 nH open-circuit, 79 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    The first Isat column, 120 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    The 1040 mW dissipated at 57 A through 0.32 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Flux swing follows Bp-p = K x L x dI. With K = 233 and a ripple of 36 A the core sees roughly 92.3 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Series Positioning

    At 13.4 x 12.7 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 110 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it the lowest inductance of the 15 parts in this data sheet, DCR sits between the 0.18 and 0.53 mOhm the series covers.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 110 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.32 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Outline Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1308R1-R11-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products