Eaton FP1308R1-R32-R - 320 nH Shielded Power Inductor 13.4 x 12.7 mm
Eaton FP1308R1-R32-R - 320 nH Shielded Power Inductor 13.4 x 12.7 mm

Eaton FP1308R1-R32-R - 320 nH Shielded Power Inductor 13.4 x 12.7 mm

Share
pEaton FP1308R1-R32-R: 320 nH high frequency, high current power inductor, 57 A Irms, 52 A Isat, DCR 0.32 mOhm, 13.4 x 12.7 mm package./p
    • Product Details
    • Download

    FP1308R1-R32-R at a glance: 320 nH high frequency, high current power inductor, 57 A Irms, 52 A Isat, DCR 0.32 mOhm, 13.4 x 12.7 mm body, 8.0 mm tall.

    Eaton FP1308R1-R32-R High frequency, high current power inductors

    The FP1308R1-R32-R is a 13.4 x 12.7 mm high frequency, high current power inductor from Eaton, rated 57 A Irms at 320 nH and 0.32 mOhm typical DCR. It is a surface-mount part 8.0 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Key Specifications

    Orderable part numberFP1308R1-R32-R
    Inductance, OCL (0 Adc)320 nH
    Inductance, FLL (minimum)230 nH
    Irms (40 °C rise, no core loss)57 A
    Isat (20% roll-off @ +25 °C)52 A
    Isat2 (20% roll-off @ +125 °C)40 A
    DCR typical @ +20 °C0.32 mOhm
    K-factor (Bp-p = K x L x dI)233
    Package13.4 x 12.7 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    320 nH open-circuit, 230 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Peak current at 20% roll-off is 52 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 1040 mW dissipated at 57 A through 0.32 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The K-factor of 233 turns ripple into flux: a peak-to-peak swing of 15.6 A gives about 116.3 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Series Positioning

    At 13.4 x 12.7 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 320 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 10 of 15 when the data sheet is sorted by inductance, DCR sits between the 0.18 and 0.53 mOhm the series covers.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    The order of checks that works: compute ripple from 320 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.32 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1308R1-R32-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products