Eaton FP1308R2-R21-R 210 nH 80 A Saturation Inductor
Eaton FP1308R2-R21-R 210 nH 80 A Saturation Inductor

Eaton FP1308R2-R21-R 210 nH 80 A Saturation Inductor

Share
pEaton FP1308R2-R21-R: 210 nH high frequency, high current power inductor, 45 A Irms, 80 A Isat, DCR 0.53 mOhm, 13.4 x 12.7 mm package./p
    • Product Details
    • Download

    FP1308R2-R21-R at a glance: 210 nH high frequency, high current power inductor, 45 A Irms, 80 A Isat, DCR 0.53 mOhm, 13.4 x 12.7 mm body, 8.0 mm tall.

    Eaton FP1308R2-R21-R High frequency, high current power inductors

    Eaton FP1308R2-R21-R is a high frequency, high current power inductor in a 13.4 x 12.7 mm surface-mount package. It carries 210 nH of open-circuit inductance with 45 A Irms and a typical DCR of 0.53 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 8.0 mm tall and rated from -40 °C to +125 °C.

    Key Specifications

    Orderable part numberFP1308R2-R21-R
    Inductance, OCL (0 Adc)210 nH
    Inductance, FLL (minimum)152 nH
    Irms (40 °C rise, no core loss)45 A
    Isat (20% roll-off @ +25 °C)80 A
    Isat2 (20% roll-off @ +125 °C)68 A
    DCR typical @ +20 °C0.53 mOhm
    K-factor (Bp-p = K x L x dI)233
    Package13.4 x 12.7 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Two inductance figures are published. 210 nH is measured with no DC in the winding, 152 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    The first Isat column, 80 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Copper loss at the rated current works out at about 1073 mW (45 A squared times 0.53 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Core loss needs flux, and flux here is about 117.4 mT for a 24 A ripple (K = 233). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Series Positioning

    At 13.4 x 12.7 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 210 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 4 of 15 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.53 mOhm, which is what the extra turns cost, Irms of 45 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 210 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.53 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1308R2-R21-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message