Eaton FP1308R2-R26-R 260 nH Power Inductor, 45 A
Eaton FP1308R2-R26-R 260 nH Power Inductor, 45 A

Eaton FP1308R2-R26-R 260 nH Power Inductor, 45 A

Share
pEaton FP1308R2-R26-R: 260 nH high frequency, high current power inductor, 45 A Irms, 64 A Isat, DCR 0.53 mOhm, 13.4 x 12.7 mm package./p
    • Product Details
    • Download

    FP1308R2-R26-R at a glance: 260 nH high frequency, high current power inductor, 45 A Irms, 64 A Isat, DCR 0.53 mOhm, 13.4 x 12.7 mm body, 8.0 mm tall.

    Eaton FP1308R2-R26-R High frequency, high current power inductors

    Eaton builds the FP1308R2-R26-R as a high frequency, high current power inductor for 13.4 x 12.7 mm footprints. At 260 nH and 45 A Irms with 0.53 mOhm of DCR it targets high-current DC-DC stages; the 8.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Ratings at a Glance

    Orderable part numberFP1308R2-R26-R
    Inductance, OCL (0 Adc)260 nH
    Inductance, FLL (minimum)187 nH
    Irms (40 °C rise, no core loss)45 A
    Isat (20% roll-off @ +25 °C)64 A
    Isat2 (20% roll-off @ +125 °C)52 A
    DCR typical @ +20 °C0.53 mOhm
    K-factor (Bp-p = K x L x dI)233
    Package13.4 x 12.7 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    At zero bias the winding measures 260 nH. Put Isat1 through it and the figure falls to 187 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 260 nH number; loop stability and worst-case current belong on the lower one.

    Peak current at 20% roll-off is 64 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Irms of 45 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.53 mOhm that is roughly 1073 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Flux swing follows Bp-p = K x L x dI. With K = 233 and a ripple of 19.2 A the core sees roughly 116.3 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    What This Family Is For

    At 13.4 x 12.7 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 260 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 7 of 15 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.53 mOhm, which is what the extra turns cost, Irms of 45 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Size the inductor on peak current first, not average. With 260 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    On the board, place the part so the switch-node copper is short and wide. At 0.53 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1308R2-R26-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products