Eaton FP1308R2-R44-R High Current Inductor, 440 nH 0.53 mOhm
Eaton FP1308R2-R44-R High Current Inductor, 440 nH 0.53 mOhm

Eaton FP1308R2-R44-R High Current Inductor, 440 nH 0.53 mOhm

Share
pEaton FP1308R2-R44-R: 440 nH high frequency, high current power inductor, 45 A Irms, 37 A Isat, DCR 0.53 mOhm, 13.4 x 12.7 mm package./p
    • Product Details
    • Download

    FP1308R2-R44-R at a glance: 440 nH high frequency, high current power inductor, 45 A Irms, 37 A Isat, DCR 0.53 mOhm, 13.4 x 12.7 mm body, 8.0 mm tall.

    Eaton FP1308R2-R44-R High frequency, high current power inductors

    The FP1308R2-R44-R is a 13.4 x 12.7 mm high frequency, high current power inductor from Eaton, rated 45 A Irms at 440 nH and 0.53 mOhm typical DCR. It is a surface-mount part 8.0 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Ratings at a Glance

    Orderable part numberFP1308R2-R44-R
    Inductance, OCL (0 Adc)440 nH
    Inductance, FLL (minimum)317 nH
    Irms (40 °C rise, no core loss)45 A
    Isat (20% roll-off @ +25 °C)37 A
    Isat2 (20% roll-off @ +125 °C)28 A
    DCR typical @ +20 °C0.53 mOhm
    K-factor (Bp-p = K x L x dI)233
    Package13.4 x 12.7 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    At zero bias the winding measures 440 nH. Put Isat1 through it and the figure falls to 317 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 440 nH number; loop stability and worst-case current belong on the lower one.

    Saturation is quoted as 20% roll-off at 37 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Copper loss at the rated current works out at about 1073 mW (45 A squared times 0.53 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The K-factor of 233 turns ripple into flux: a peak-to-peak swing of 11.1 A gives about 113.8 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Where This Part Sits in the Range

    At 13.4 x 12.7 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 440 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 13 of 15 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.53 mOhm, which is what the extra turns cost, Irms of 45 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    The order of checks that works: compute ripple from 440 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.53 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Outline Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1308R2-R44-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products