Eaton FP1308R3-R11-R 68 A SMD Power Inductor, 110 nH
Eaton FP1308R3-R11-R 68 A SMD Power Inductor, 110 nH

Eaton FP1308R3-R11-R 68 A SMD Power Inductor, 110 nH

Share
pEaton FP1308R3-R11-R: 110 nH high frequency, high current power inductor, 68 A Irms, 120 A Isat, DCR 0.18 mOhm, 13.4 x 12.7 mm package./p
    • Product Details
    • Download

    FP1308R3-R11-R at a glance: 110 nH high frequency, high current power inductor, 68 A Irms, 120 A Isat, DCR 0.18 mOhm, 13.4 x 12.7 mm body, 8.0 mm tall.

    Eaton FP1308R3-R11-R High frequency, high current power inductors

    The FP1308R3-R11-R is a 13.4 x 12.7 mm high frequency, high current power inductor from Eaton, rated 68 A Irms at 110 nH and 0.18 mOhm typical DCR. It is a surface-mount part 8.0 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Electrical Specifications

    Orderable part numberFP1308R3-R11-R
    Inductance, OCL (0 Adc)110 nH
    Inductance, FLL (minimum)79 nH
    Irms (40 °C rise, no core loss)68 A
    Isat (20% roll-off @ +25 °C)120 A
    Isat2 (20% roll-off @ +125 °C)105 A
    DCR typical @ +20 °C0.18 mOhm
    K-factor (Bp-p = K x L x dI)233
    Package13.4 x 12.7 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Two inductance figures are published. 110 nH is measured with no DC in the winding, 79 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    The first Isat column, 120 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    The 832 mW dissipated at 68 A through 0.18 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The K-factor of 233 turns ripple into flux: a peak-to-peak swing of 36 A gives about 92.3 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Series Positioning

    At 13.4 x 12.7 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 110 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it the lowest inductance of the 15 parts in this data sheet, and it shares the lowest DCR here at 0.18 mOhm, Irms of 68 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Size the inductor on peak current first, not average. With 110 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    On the board, place the part so the switch-node copper is short and wide. At 0.18 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1308R3-R11-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message