Eaton FP1308R3-R21-R 210 nH 80 A Saturation Inductor
Eaton FP1308R3-R21-R 210 nH 80 A Saturation Inductor

Eaton FP1308R3-R21-R 210 nH 80 A Saturation Inductor

Share
pEaton FP1308R3-R21-R: 210 nH high frequency, high current power inductor, 68 A Irms, 80 A Isat, DCR 0.18 mOhm, 13.4 x 12.7 mm package./p
    • Product Details
    • Download

    FP1308R3-R21-R at a glance: 210 nH high frequency, high current power inductor, 68 A Irms, 80 A Isat, DCR 0.18 mOhm, 13.4 x 12.7 mm body, 8.0 mm tall.

    Eaton FP1308R3-R21-R High frequency, high current power inductors

    FP1308R3-R21-R is one of Eaton's high frequency, high current power inductor series, 13.4 x 12.7 mm with a 8.0 mm tall profile. Electrically it offers 210 nH at 68 A Irms and 0.18 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Ratings at a Glance

    Orderable part numberFP1308R3-R21-R
    Inductance, OCL (0 Adc)210 nH
    Inductance, FLL (minimum)152 nH
    Irms (40 °C rise, no core loss)68 A
    Isat (20% roll-off @ +25 °C)80 A
    Isat2 (20% roll-off @ +125 °C)68 A
    DCR typical @ +20 °C0.18 mOhm
    K-factor (Bp-p = K x L x dI)233
    Package13.4 x 12.7 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    At zero bias the winding measures 210 nH. Put Isat1 through it and the figure falls to 152 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 210 nH number; loop stability and worst-case current belong on the lower one.

    Peak current at 20% roll-off is 80 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 832 mW dissipated at 68 A through 0.18 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Core loss needs flux, and flux here is about 117.4 mT for a 24 A ripple (K = 233). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Series Positioning

    At 13.4 x 12.7 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 210 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 4 of 15 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.18 mOhm, Irms of 68 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Size the inductor on peak current first, not average. With 210 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.18 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1308R3-R21-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products