
FP1308R3-R26-R at a glance: 260 nH high frequency, high current power inductor, 68 A Irms, 64 A Isat, DCR 0.18 mOhm, 13.4 x 12.7 mm body, 8.0 mm tall.
Eaton FP1308R3-R26-R is a high frequency, high current power inductor in a 13.4 x 12.7 mm surface-mount package. It carries 260 nH of open-circuit inductance with 68 A Irms and a typical DCR of 0.18 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 8.0 mm tall and rated from -40 °C to +125 °C.
| Orderable part number | FP1308R3-R26-R |
| Inductance, OCL (0 Adc) | 260 nH |
| Inductance, FLL (minimum) | 187 nH |
| Irms (40 °C rise, no core loss) | 68 A |
| Isat (20% roll-off @ +25 °C) | 64 A |
| Isat2 (20% roll-off @ +125 °C) | 52 A |
| DCR typical @ +20 °C | 0.18 mOhm |
| K-factor (Bp-p = K x L x dI) | 233 |
| Package | 13.4 x 12.7 mm, 8.0 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
Two inductance figures are published. 260 nH is measured with no DC in the winding, 187 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.
The first Isat column, 64 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.
The 832 mW dissipated at 68 A through 0.18 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.
Core loss needs flux, and flux here is about 116.3 mT for a 19.2 A ripple (K = 233). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.
At 13.4 x 12.7 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 260 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.
That makes it part 7 of 15 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.18 mOhm, Irms of 68 A is the top of the family.
Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 260 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.
Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.18 mOhm the winding is not the loss, the trace can be.
The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
Why does DCR have both a typical and a maximum figure?
The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd