Eaton FP1309B1-R100-R 60 A SMD Power Inductor, 100 nH
Eaton FP1309B1-R100-R 60 A SMD Power Inductor, 100 nH

Eaton FP1309B1-R100-R 60 A SMD Power Inductor, 100 nH

Share
pEaton FP1309B1-R100-R: 100 nH high frequency, high current power inductor, 60 A Irms, 100 A Isat, DCR 0.19 mOhm, 12.8 x 8.3 mm package./p
    • Product Details
    • Download

    FP1309B1-R100-R at a glance: 100 nH high frequency, high current power inductor, 60 A Irms, 100 A Isat, DCR 0.19 mOhm, 12.8 x 8.3 mm body, 8.8 mm tall.

    Eaton FP1309B1-R100-R High frequency, high current power inductors

    Eaton builds the FP1309B1-R100-R as a high frequency, high current power inductor for 12.8 x 8.3 mm footprints. At 100 nH and 60 A Irms with 0.19 mOhm of DCR it targets high-current DC-DC stages; the 8.8 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Specification Table

    Orderable part numberFP1309B1-R100-R
    Inductance, OCL (0 Adc)100 nH
    Inductance, FLL (minimum)72 nH
    Irms (40 °C rise, no core loss)60 A
    Isat (20% roll-off @ +25 °C)100 A
    Isat2 (20% roll-off @ +125 °C)80 A
    DCR typical @ +20 °C0.19 mOhm
    K-factor (Bp-p = K x L x dI)296
    Package12.8 x 8.3 mm, 8.8 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    Two inductance figures are published. 100 nH is measured with no DC in the winding, 72 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Peak current at 20% roll-off is 100 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Irms of 60 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.19 mOhm that is roughly 684 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Flux swing follows Bp-p = K x L x dI. With K = 296 and a ripple of 30 A the core sees roughly 88.8 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Where This Part Sits in the Range

    At 12.8 x 8.3 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 100 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it the lowest inductance of the 3 parts in this data sheet.

    • Application fit: Servers, Multi-phase and Vcore regulators, Data centers, networking and storage systems.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 100 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.19 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1309B1-R100-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products