Eaton FP1309B1-R120-R 120 nH 90 A Saturation Inductor
Eaton FP1309B1-R120-R 120 nH 90 A Saturation Inductor

Eaton FP1309B1-R120-R 120 nH 90 A Saturation Inductor

Share
pEaton FP1309B1-R120-R: 120 nH high frequency, high current power inductor, 60 A Irms, 90 A Isat, DCR 0.19 mOhm, 12.8 x 8.3 mm package./p
    • Product Details
    • Download

    FP1309B1-R120-R at a glance: 120 nH high frequency, high current power inductor, 60 A Irms, 90 A Isat, DCR 0.19 mOhm, 12.8 x 8.3 mm body, 8.8 mm tall.

    Eaton FP1309B1-R120-R High frequency, high current power inductors

    Eaton builds the FP1309B1-R120-R as a high frequency, high current power inductor for 12.8 x 8.3 mm footprints. At 120 nH and 60 A Irms with 0.19 mOhm of DCR it targets high-current DC-DC stages; the 8.8 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Specification Table

    Orderable part numberFP1309B1-R120-R
    Inductance, OCL (0 Adc)120 nH
    Inductance, FLL (minimum)87 nH
    Irms (40 °C rise, no core loss)60 A
    Isat (20% roll-off @ +25 °C)90 A
    Isat2 (20% roll-off @ +125 °C)72 A
    DCR typical @ +20 °C0.19 mOhm
    K-factor (Bp-p = K x L x dI)296
    Package12.8 x 8.3 mm, 8.8 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    120 nH open-circuit, 87 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Saturation is quoted as 20% roll-off at 90 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Irms of 60 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.19 mOhm that is roughly 684 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Flux swing follows Bp-p = K x L x dI. With K = 296 and a ripple of 27 A the core sees roughly 95.9 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Where This Part Sits in the Range

    At 12.8 x 8.3 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 120 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 2 of 3 when the data sheet is sorted by inductance.

    • Application fit: Servers, Multi-phase and Vcore regulators, Data centers, networking and storage systems.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 120 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.19 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1309B1-R120-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products