Eaton FP1505R1-R40-R - 400 nH Shielded Power Inductor 7.0 x 15.0 mm
Eaton FP1505R1-R40-R - 400 nH Shielded Power Inductor 7.0 x 15.0 mm

Eaton FP1505R1-R40-R - 400 nH Shielded Power Inductor 7.0 x 15.0 mm

Share
pEaton FP1505R1-R40-R: 400 nH high frequency, high current power inductor, 53 A Irms, 24 A Isat, DCR 0.47 mOhm, 7.0 x 15.0 mm package./p
    • Product Details
    • Download

    FP1505R1-R40-R at a glance: 400 nH high frequency, high current power inductor, 53 A Irms, 24 A Isat, DCR 0.47 mOhm, 7.0 x 15.0 mm body, 5.0 mm tall.

    Eaton FP1505R1-R40-R High frequency, high current power inductors

    Eaton FP1505R1-R40-R is a high frequency, high current power inductor in a 7.0 x 15.0 mm surface-mount package. It carries 400 nH of open-circuit inductance with 53 A Irms and a typical DCR of 0.47 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 5.0 mm tall and rated from -40 °C to +125 °C.

    Key Specifications

    Orderable part numberFP1505R1-R40-R
    Inductance, OCL (0 Adc)400 nH
    Inductance, FLL (minimum)288 nH
    Irms (40 °C rise, no core loss)53 A
    Isat (20% roll-off @ +25 °C)24 A
    Isat2 (20% roll-off @ +125 °C)19.5 A
    DCR typical @ +20 °C0.47 mOhm
    K-factor (Bp-p = K x L x dI)356.3
    Package7.0 x 15.0 mm, 5.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    At zero bias the winding measures 400 nH. Put Isat1 through it and the figure falls to 288 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 400 nH number; loop stability and worst-case current belong on the lower one.

    The first Isat column, 24 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    The 1320 mW dissipated at 53 A through 0.47 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Core loss needs flux, and flux here is about 102.6 mT for a 7.2 A ripple (K = 356.3). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Series Positioning

    At 7.0 x 15.0 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 400 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it the highest inductance of the 6 parts in this data sheet.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 400 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.47 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1505R1-R40-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products