Eaton FP1507R1-R185-R High Current Inductor, 185 nH 0.52 mOhm
Eaton FP1507R1-R185-R High Current Inductor, 185 nH 0.52 mOhm

Eaton FP1507R1-R185-R High Current Inductor, 185 nH 0.52 mOhm

Share
pEaton FP1507R1-R185-R: 185 nH high current power inductor, 45 A Irms, 40 A Isat, DCR 0.52 mOhm, 15.1 x 8.5 mm package./p
    • Product Details
    • Download

    FP1507R1-R185-R at a glance: 185 nH high current power inductor, 45 A Irms, 40 A Isat, DCR 0.52 mOhm, 15.1 x 8.5 mm body, 6.7 mm tall.

    Eaton FP1507R1-R185-R High current power inductors

    Eaton FP1507R1-R185-R is a high current power inductor in a 15.1 x 8.5 mm surface-mount package. It carries 185 nH of open-circuit inductance with 45 A Irms and a typical DCR of 0.52 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 6.7 mm tall and rated from -55 °C to +125 °C.

    Ratings at a Glance

    Orderable part numberFP1507R1-R185-R
    Inductance, OCL (0 Adc)185 nH
    Inductance, FLL (minimum)163 nH
    Irms (40 °C rise, no core loss)45 A
    Isat (2% roll-off @ +25 °C)40 A
    DCR typical @ +20 °C0.52 mOhm
    Package15.1 x 8.5 mm, 6.7 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-55 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    185 nH open-circuit, 163 nH at full load: that is a 12% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    The first Isat column, 40 A at +25 °C, is the peak the part takes at 2% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Copper loss at the rated current works out at about 1053 mW (45 A squared times 0.52 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.

    Where This Part Sits in the Range

    At 15.1 x 8.5 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 185 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    • Application fit: Compatible with Picor® Cool-Power® ZVS Buck and Buck-Boost Regulator Families.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -55 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 185 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.52 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1507R1-R185-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message