
FP2-S100-R at a glance: 100 nH high current power inductor, 39 A Irms, 22 A Isat, DCR 0.24 mOhm, 7.2 x 6.7 mm body, 3.0 mm or 5.0 mm tall.
Eaton builds the FP2-S100-R as a high current power inductor for 7.2 x 6.7 mm footprints. At 100 nH and 39 A Irms with 0.24 mOhm of DCR it targets high-current DC-DC stages; the 3.0 mm or 5.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.
| Orderable part number | FP2-S100-R |
| Inductance, OCL (0 Adc) | 100 nH |
| Irms (40 °C rise, no core loss) | 39 A |
| Isat (30% roll-off @ +20 °C) | 22 A |
| DCR typical @ +20 °C | 0.24 mOhm |
| Volt-microsecond rating | 0.75 V-us |
| Package | 7.2 x 6.7 mm, 3.0 mm / 5.0 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
Only the open-circuit value, 100 nH, is tabulated here. With DC in the winding the core will show less, so treat 100 nH as a ceiling rather than an operating value.
Saturation is quoted as 30% roll-off at 22 A at +20 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.
Irms of 39 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.24 mOhm that is roughly 365 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.
The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.
This is one of the smaller bodies in the FP range. At 7.2 x 6.7 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 100 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.
That makes it part 8 of 15 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.24 mOhm, Irms of 39 A is the top of the family.
The order of checks that works: compute ripple from 100 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.
On the board, place the part so the switch-node copper is short and wide. At 0.24 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

What does the R suffix on the part number mean?
It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.
Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd