Eaton FP2-V120-R - 120 nH Shielded Power Inductor 7.2 x 6.7 mm
Eaton FP2-V120-R - 120 nH Shielded Power Inductor 7.2 x 6.7 mm

Eaton FP2-V120-R - 120 nH Shielded Power Inductor 7.2 x 6.7 mm

Share
pEaton FP2-V120-R: 120 nH high current power inductor, 37 A Irms, 33 A Isat, DCR 0.28 mOhm, 7.2 x 6.7 mm package./p
    • Product Details
    • Download

    FP2-V120-R at a glance: 120 nH high current power inductor, 37 A Irms, 33 A Isat, DCR 0.28 mOhm, 7.2 x 6.7 mm body, 3.0 mm or 5.0 mm tall.

    Eaton FP2-V120-R High current power inductors

    Eaton builds the FP2-V120-R as a high current power inductor for 7.2 x 6.7 mm footprints. At 120 nH and 37 A Irms with 0.28 mOhm of DCR it targets high-current DC-DC stages; the 3.0 mm or 5.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Key Specifications

    Orderable part numberFP2-V120-R
    Inductance, OCL (0 Adc)120 nH
    Irms (40 °C rise, no core loss)37 A
    Isat (30% roll-off @ +20 °C)33 A
    DCR typical @ +20 °C0.28 mOhm
    Volt-microsecond rating0.99 V-us
    Package7.2 x 6.7 mm, 3.0 mm / 5.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    120 nH is the unbiased inductance. The data sheet does not publish a separate full-load figure for this part, so leave margin when you compute ripple at rated current.

    The first Isat column, 33 A at +20 °C, is the peak the part takes at 30% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Copper loss at the rated current works out at about 383 mW (37 A squared times 0.28 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.

    What This Family Is For

    This is one of the smaller bodies in the FP range. At 7.2 x 6.7 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 120 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 11 of 15 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.28 mOhm, which is what the extra turns cost, Irms of 37 A is the bottom of the family.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 120 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.28 mOhm the winding is not the loss, the trace can be.

    Outline Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP2-V120-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products