Eaton FP3-1R0-R - 1.1 uH Shielded Power Inductor 7.25 x 6.7 mm
Eaton FP3-1R0-R - 1.1 uH Shielded Power Inductor 7.25 x 6.7 mm

Eaton FP3-1R0-R - 1.1 uH Shielded Power Inductor 7.25 x 6.7 mm

Share
pEaton FP3-1R0-R: 1.1 uH high current, low profile inductor, 6.26 A Irms, 7.4 A Isat, DCR 9.4 mOhm, 7.25 x 6.7 mm package./p
    • Product Details
    • Download

    FP3-1R0-R at a glance: 1.1 uH high current, low profile inductor, 6.26 A Irms, 7.4 A Isat, DCR 9.4 mOhm, 7.25 x 6.7 mm body, 3.0 mm tall.

    Eaton FP3-1R0-R High current, low profile inductors

    Eaton FP3-1R0-R is a high current, low profile inductor in a 7.25 x 6.7 mm surface-mount package. It carries 1.1 uH of open-circuit inductance with 6.26 A Irms and a typical DCR of 9.4 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 3.0 mm tall and rated from -40 °C to +155 °C.

    Specification Table

    Orderable part numberFP3-1R0-R
    Inductance, OCL (0 Adc)1.1 uH
    Irms (40 °C rise, no core loss)6.26 A
    Isat7.4 A
    Isat29.5 A
    DCR typical @ +20 °C9.4 mOhm
    DCR maximum @ +20 °C11.2 mOhm
    K-factor (Bp-p = K x L x dI)219
    Package7.25 x 6.7 mm, 3.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +155 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    1.1 uH is the unbiased inductance. The data sheet does not publish a separate full-load figure for this part, so leave margin when you compute ripple at rated current.

    The first Isat column, 7.4 A, is the peak the part takes at the quoted roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    The 368 mW dissipated at 6.26 A through 9.4 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Flux swing follows Bp-p = K x L x dI. With K = 219 and a ripple of 2.22 A the core sees roughly 53.5 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Positioning in the FP Range

    This is one of the smaller bodies in the FP range. At 7.25 x 6.7 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 1.1 uH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 5 of 12 when the data sheet is sorted by inductance, DCR sits between the 1 and 106 mOhm the series covers.

    • Application fit: Voltage Regulator Modules (VRMs), Multi-phase regulators, Desktop and server VRMs and EVRDs.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +155 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 1.1 uH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 9.4 mOhm the winding is not the loss, the trace can be.

    Outline Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP3-1R0-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products