Eaton FPT1006-340-R - 340 nH Shielded Power Inductor 10.5 x 8.8 mm
Eaton FPT1006-340-R - 340 nH Shielded Power Inductor 10.5 x 8.8 mm

Eaton FPT1006-340-R - 340 nH Shielded Power Inductor 10.5 x 8.8 mm

Share
Eaton FPT1006-340-R: 340 nH dual conductor high current power inductor, 19 A Irms, 40.5 A Isat, DCR 1 mOhm, 10.5 x 8.8 mm package.
    • Product Details
    • Download

    FPT1006-340-R at a glance: 340 nH dual conductor high current power inductor, 19 A Irms, 40.5 A Isat, DCR 1 mOhm, 10.5 x 8.8 mm body, 6.4 mm tall.

    Eaton FPT1006-340-R Dual conductor high current power inductor

    Eaton builds the FPT1006-340-R as a dual conductor high current power inductor for 10.5 x 8.8 mm footprints. At 340 nH and 19 A Irms with 1 mOhm of DCR it targets high-current DC-DC stages; the 6.4 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Key Specifications

    Orderable part numberFPT1006-340-R
    Inductance, OCL (0 Adc)340 nH
    Irms (40 °C rise, no core loss)19 A
    Isat (5% roll-off @ +25 °C)40.5 A
    DCR typical @ +20 °C1 mOhm
    Package10.5 x 8.8 mm, 6.4 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    Only the open-circuit value, 340 nH, is tabulated here. With DC in the winding the core will show less, so treat 340 nH as a ceiling rather than an operating value.

    Peak current at 5% roll-off is 40.5 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Irms of 19 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 1 mOhm that is roughly 361 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.

    What This Family Is For

    The 10.5 x 8.8 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 340 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it the lowest inductance of the 4 parts in this data sheet.

    • Application fit: Compatible with Picor® Cool-Power® ZVS Buck and Buck-Boost Regulator Families.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 340 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 1 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FPT1006-340-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message