Eaton FPT1006-500-R 19 A SMD Power Inductor, 500 nH
Eaton FPT1006-500-R 19 A SMD Power Inductor, 500 nH

Eaton FPT1006-500-R 19 A SMD Power Inductor, 500 nH

Share
Eaton FPT1006-500-R: 500 nH dual conductor high current power inductor, 19 A Irms, 27.5 A Isat, DCR 1 mOhm, 10.5 x 8.8 mm package.
    • Product Details
    • Download

    FPT1006-500-R at a glance: 500 nH dual conductor high current power inductor, 19 A Irms, 27.5 A Isat, DCR 1 mOhm, 10.5 x 8.8 mm body, 6.4 mm tall.

    Eaton FPT1006-500-R Dual conductor high current power inductor

    Eaton FPT1006-500-R is a dual conductor high current power inductor in a 10.5 x 8.8 mm surface-mount package. It carries 500 nH of open-circuit inductance with 19 A Irms and a typical DCR of 1 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 6.4 mm tall and rated from -40 °C to +125 °C.

    Specification Table

    Orderable part numberFPT1006-500-R
    Inductance, OCL (0 Adc)500 nH
    Irms (40 °C rise, no core loss)19 A
    Isat (5% roll-off @ +25 °C)27.5 A
    DCR typical @ +20 °C1 mOhm
    Package10.5 x 8.8 mm, 6.4 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    500 nH is the unbiased inductance. The data sheet does not publish a separate full-load figure for this part, so leave margin when you compute ripple at rated current.

    Peak current at 5% roll-off is 27.5 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Copper loss at the rated current works out at about 361 mW (19 A squared times 1 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.

    Positioning in the FP Range

    The 10.5 x 8.8 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 500 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 3 of 4 when the data sheet is sorted by inductance.

    • Application fit: Compatible with Picor® Cool-Power® ZVS Buck and Buck-Boost Regulator Families.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 500 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 1 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FPT1006-500-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products