Eaton FPT705-170-R 170 nH Power Inductor, 13 A
Eaton FPT705-170-R 170 nH Power Inductor, 13 A

Eaton FPT705-170-R 170 nH Power Inductor, 13 A

Share
Eaton FPT705-170-R: 170 nH dual conductor, high current power inductor, 13 A Irms, 31 A Isat, DCR 0.65 mOhm, 8.3 x 7.5 mm package.
    • Product Details
    • Download

    FPT705-170-R at a glance: 170 nH dual conductor, high current power inductor, 13 A Irms, 31 A Isat, DCR 0.65 mOhm, 8.3 x 7.5 mm body, 5.35 mm tall.

    Eaton FPT705-170-R Dual conductor, high current power inductors

    Eaton FPT705-170-R is a dual conductor, high current power inductor in a 8.3 x 7.5 mm surface-mount package. It carries 170 nH of open-circuit inductance with 13 A Irms and a typical DCR of 0.65 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 5.35 mm tall and rated from -55 °C to +125 °C.

    Ratings at a Glance

    Orderable part numberFPT705-170-R
    Inductance, OCL (0 Adc)170 nH
    Irms (40 °C rise, no core loss)13 A
    Isat31 A
    DCR typical @ +20 °C0.65 mOhm
    Package8.3 x 7.5 mm, 5.35 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-55 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    170 nH is the unbiased inductance. The data sheet does not publish a separate full-load figure for this part, so leave margin when you compute ripple at rated current.

    Saturation is quoted as the quoted roll-off at 31 A. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    The 110 mW dissipated at 13 A through 0.65 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.

    Where This Part Sits in the Range

    The 8.3 x 7.5 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 170 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it the lowest inductance of the 6 parts in this data sheet.

    • Application fit: Compatible with Picor® Cool-Power® ZVS Buck and Buck-Boost Regulator Families (Picor part number series PI33xx and PI34xx).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -55 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    The order of checks that works: compute ripple from 170 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.65 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FPT705-170-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products