Eaton FPT705-190-R - 190 nH Shielded Power Inductor 8.3 x 7.5 mm
Eaton FPT705-190-R - 190 nH Shielded Power Inductor 8.3 x 7.5 mm

Eaton FPT705-190-R - 190 nH Shielded Power Inductor 8.3 x 7.5 mm

Share
Eaton FPT705-190-R: 190 nH dual conductor, high current power inductor, 13 A Irms, 28 A Isat, DCR 0.65 mOhm, 8.3 x 7.5 mm package.
    • Product Details
    • Download

    FPT705-190-R at a glance: 190 nH dual conductor, high current power inductor, 13 A Irms, 28 A Isat, DCR 0.65 mOhm, 8.3 x 7.5 mm body, 5.35 mm tall.

    Eaton FPT705-190-R Dual conductor, high current power inductors

    Eaton builds the FPT705-190-R as a dual conductor, high current power inductor for 8.3 x 7.5 mm footprints. At 190 nH and 13 A Irms with 0.65 mOhm of DCR it targets high-current DC-DC stages; the 5.35 mm tall body keeps the height budget in check, and the part is rated from -55 °C to +125 °C.

    Specification Table

    Orderable part numberFPT705-190-R
    Inductance, OCL (0 Adc)190 nH
    Irms (40 °C rise, no core loss)13 A
    Isat28 A
    DCR typical @ +20 °C0.65 mOhm
    Package8.3 x 7.5 mm, 5.35 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-55 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Only the open-circuit value, 190 nH, is tabulated here. With DC in the winding the core will show less, so treat 190 nH as a ceiling rather than an operating value.

    Peak current at the quoted roll-off is 28 A. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 110 mW dissipated at 13 A through 0.65 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.

    Positioning in the FP Range

    The 8.3 x 7.5 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 190 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 2 of 6 when the data sheet is sorted by inductance.

    • Application fit: Compatible with Picor® Cool-Power® ZVS Buck and Buck-Boost Regulator Families (Picor part number series PI33xx and PI34xx).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -55 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Size the inductor on peak current first, not average. With 190 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.65 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FPT705-190-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products