
FPT705-200-R at a glance: 200 nH dual conductor, high current power inductor, 13 A Irms, 25 A Isat, DCR 0.65 mOhm, 8.3 x 7.5 mm body, 5.35 mm tall.
Eaton FPT705-200-R is a dual conductor, high current power inductor in a 8.3 x 7.5 mm surface-mount package. It carries 200 nH of open-circuit inductance with 13 A Irms and a typical DCR of 0.65 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 5.35 mm tall and rated from -55 °C to +125 °C.
| Orderable part number | FPT705-200-R |
| Inductance, OCL (0 Adc) | 200 nH |
| Irms (40 °C rise, no core loss) | 13 A |
| Isat | 25 A |
| DCR typical @ +20 °C | 0.65 mOhm |
| Package | 8.3 x 7.5 mm, 5.35 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -55 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
200 nH is the unbiased inductance. The data sheet does not publish a separate full-load figure for this part, so leave margin when you compute ripple at rated current.
Peak current at the quoted roll-off is 25 A. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.
Irms of 13 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.65 mOhm that is roughly 110 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.
The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.
The 8.3 x 7.5 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 200 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.
That makes it part 3 of 6 when the data sheet is sorted by inductance.
The order of checks that works: compute ripple from 200 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.
On the board, place the part so the switch-node copper is short and wide. At 0.65 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.
The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

Why does DCR have both a typical and a maximum figure?
The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.
What does the R suffix on the part number mean?
It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd