
FPT705-270-R at a glance: 270 nH dual conductor, high current power inductor, 13 A Irms, 19 A Isat, DCR 0.65 mOhm, 8.3 x 7.5 mm body, 5.35 mm tall.
Eaton builds the FPT705-270-R as a dual conductor, high current power inductor for 8.3 x 7.5 mm footprints. At 270 nH and 13 A Irms with 0.65 mOhm of DCR it targets high-current DC-DC stages; the 5.35 mm tall body keeps the height budget in check, and the part is rated from -55 °C to +125 °C.
| Orderable part number | FPT705-270-R |
| Inductance, OCL (0 Adc) | 270 nH |
| Irms (40 °C rise, no core loss) | 13 A |
| Isat | 19 A |
| DCR typical @ +20 °C | 0.65 mOhm |
| Package | 8.3 x 7.5 mm, 5.35 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -55 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
270 nH is the unbiased inductance. The data sheet does not publish a separate full-load figure for this part, so leave margin when you compute ripple at rated current.
The first Isat column, 19 A, is the peak the part takes at the quoted roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.
The 110 mW dissipated at 13 A through 0.65 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.
The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.
The 8.3 x 7.5 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 270 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.
That makes it part 5 of 6 when the data sheet is sorted by inductance.
Size the inductor on peak current first, not average. With 270 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.
Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.65 mOhm the winding is not the loss, the trace can be.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

Why does DCR have both a typical and a maximum figure?
The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.
What does the R suffix on the part number mean?
It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd