Eaton FPT705-300-R 300 nH Power Inductor, 13 A
Eaton FPT705-300-R 300 nH Power Inductor, 13 A

Eaton FPT705-300-R 300 nH Power Inductor, 13 A

Share
Eaton FPT705-300-R: 300 nH dual conductor, high current power inductor, 13 A Irms, 17 A Isat, DCR 0.65 mOhm, 8.3 x 7.5 mm package.
    • Product Details
    • Download

    FPT705-300-R at a glance: 300 nH dual conductor, high current power inductor, 13 A Irms, 17 A Isat, DCR 0.65 mOhm, 8.3 x 7.5 mm body, 5.35 mm tall.

    Eaton FPT705-300-R Dual conductor, high current power inductors

    FPT705-300-R is one of Eaton's dual conductor, high current power inductor series, 8.3 x 7.5 mm with a 5.35 mm tall profile. Electrically it offers 300 nH at 13 A Irms and 0.65 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Electrical Specifications

    Orderable part numberFPT705-300-R
    Inductance, OCL (0 Adc)300 nH
    Irms (40 °C rise, no core loss)13 A
    Isat17 A
    DCR typical @ +20 °C0.65 mOhm
    Package8.3 x 7.5 mm, 5.35 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-55 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Only the open-circuit value, 300 nH, is tabulated here. With DC in the winding the core will show less, so treat 300 nH as a ceiling rather than an operating value.

    Peak current at the quoted roll-off is 17 A. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Irms of 13 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.65 mOhm that is roughly 110 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.

    Positioning in the FP Range

    The 8.3 x 7.5 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 300 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it the highest inductance of the 6 parts in this data sheet.

    • Application fit: Compatible with Picor® Cool-Power® ZVS Buck and Buck-Boost Regulator Families (Picor part number series PI33xx and PI34xx).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -55 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    Size the inductor on peak current first, not average. With 300 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    On the board, place the part so the switch-node copper is short and wide. At 0.65 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Outline Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FPT705-300-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products