Eaton HC1-5R1-R Foil-Wound Inductor 5.15 uH, Isat 11.2 A
Eaton HC1-5R1-R Foil-Wound Inductor 5.15 uH, Isat 11.2 A

Eaton HC1-5R1-R Foil-Wound Inductor 5.15 uH, Isat 11.2 A

Share
Eaton HC1-5R1-R: foil-wound high-current inductor, 5.15 uH ±15%, 12.8 A Irms, Isat 11.2 A, DCR 5.7 mOhm, 13.0 x 10.0 mm.
    • Product Details
    • Download

    Eaton HC1-5R1-R Foil-Wound Inductor 5.15 uH, Isat 11.2 A

    HC1-5R1-R at a glance: foil-wound high-current inductor, 5.15 uH ±15%, 12.8 A Irms, Isat 11.2 A (30% rolloff @ +20 °C), DCR 5.7 mOhm, 13.0 x 10.0 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHC1-5R1-R
    OCL (open circuit inductance)5.15 uH ±15%
    Irms (DC, 40 °C rise)12.8 A
    Isat (30% rolloff @ +20 °C)11.2 A
    DCR typical @ +20 °C5.7 mOhm
    Volt-time rating (V-us)11
    Package13.0 x 10.0 mm
    Height4.9 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4328

    Mechanical Drawing

    HC1-5R1-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4328: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    This part belongs to the HC foil family, built for high-current, low-voltage converters where efficiency is dominated by the copper. Ferrite keeps core loss low at the switching frequency; the foil winding keeps the copper loss low at the DC component. Both halves of the loss budget are addressed in the same body.

    At the rated 12.8 A the winding dissipates about 0.932 W in copper alone, using the typical DCR of 5.7 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Saturation is quoted as 30% rolloff @ +20 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    The core stores roughly 323 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    Where This Series Fits

    The HC foil family covers the low-inductance, very-high-current end of the range: sub-microhenry to a few microhenry, with DC resistance measured in fractions of a milliohm. It is the family to reach for when the rail is a volt or two and the current is tens of amps.

    The HC1 family spans 0.218 uH to 10.5 uH; this row sits at position 9 of 11.

    Compared with its neighbours in the table, HC1-7R8-R trades 3.97 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: foil winding, ferrite core, 13.0 x 10.0 mm body at 4.9 mm.
    • Typical applications: distributed power systems dc-dc converters; general-purpose low voltage supplies; computer systems; servers; industrial equipment; data networking and storage systems.
    • The rated current assumes a 40 °C rise from DC alone. AC ripple raises the winding temperature further, and the derating curves in the data sheet are there for exactly that case.

    Putting It to Work

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 5.7 mOhm becomes roughly 8.05 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: on a low-voltage rail the DCR drop is a real fraction of the output. Compare the millivolt drop at rated current against the converter tolerance before choosing the smallest inductance in the family.

    • At frequencies above a few hundred kilohertz, check the AC resistance rise before assuming the DC figure holds.
    • Leave clearance for the tape-and-reel orientation if the line places by vision.
    • Keep the peak current inside the saturation boundary with margin for inductance tolerance.

    Frequently Asked Questions

    Is the part suitable for a SEPIC or buck-boost stage?
    The inductance and current ratings suit it, but check the AC flux swing: in a buck-boost the inductor carries the full input current continuously, so the core loss is higher than in a buck stage of the same output.

    Why foil instead of round wire?
    At high frequency the current crowds into the surface of the conductor. A flat foil presents a wide surface for the same cross-section, so the AC resistance stays closer to the DC value and the winding runs cooler.

    What does the DCR tolerance mean for paralleling?
    Parts are not matched for DCR, so two in parallel will not share current exactly. The mismatch is set by the DCR tolerance, and because the DCR is only fractions of a milliohm, a small absolute difference is a large percentage one.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products