Eaton HC1-R30-R 0.291 uH High-Current Inductor 0.36 mOhm
Eaton HC1-R30-R 0.291 uH High-Current Inductor 0.36 mOhm

Eaton HC1-R30-R 0.291 uH High-Current Inductor 0.36 mOhm

Share
Eaton HC1-R30-R: foil-wound high-current inductor, 0.291 uH ±15%, 51.4 A Irms, Isat 31.8 A, DCR 0.36 mOhm, 13.0 x 10.0 mm.
    • Product Details
    • Download

    Eaton HC1-R30-R 0.291 uH High-Current Inductor 0.36 mOhm

    HC1-R30-R at a glance: foil-wound high-current inductor, 0.291 uH ±15%, 51.4 A Irms, Isat 31.8 A (30% rolloff @ +20 °C), DCR 0.36 mOhm, 13.0 x 10.0 mm.

    Specification Table

    ParameterValue
    Orderable part numberHC1-R30-R
    OCL (open circuit inductance)0.291 uH ±15%
    Irms (DC, 40 °C rise)51.4 A
    Isat (30% rolloff @ +20 °C)31.8 A
    DCR typical @ +20 °C0.36 mOhm
    Volt-time rating (V-us)1.83
    Package13.0 x 10.0 mm
    Height4.9 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4328

    Mechanical Drawing

    HC1-R30-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4328: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Where a power rail delivers tens of amps at a volt or two, the inductor is effectively a short circuit that happens to store energy. The foil construction here minimises the resistance of that short circuit while the ferrite core holds the inductance, which is why the family is used on distributed power and server-class converters.

    With 0.36 mOhm typical, the I-squared-R loss at the full 51.4 A rating is about 0.952 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The saturation rating reads 30% rolloff @ +20 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    The core stores roughly 147 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    Positioning in the Range

    The HC foil family covers the low-inductance, very-high-current end of the range: sub-microhenry to a few microhenry, with DC resistance measured in fractions of a milliohm. It is the family to reach for when the rail is a volt or two and the current is tens of amps.

    Within the HC1 family this is value 2 of 11, in a range that runs from 0.218 uH to 10.5 uH.

    The next value up in the same family, HC1-R57-R, gives 0.572 uH at 37.8 A and DCR 0.68 mOhm: the extra inductance costs about 13.6 A of rated current.

    • Core material: foil winding, ferrite core, 13.0 x 10.0 mm body at 4.9 mm.
    • Typical applications: distributed power systems dc-dc converters; general-purpose low voltage supplies; computer systems; servers; industrial equipment; data networking and storage systems.
    • The rated current assumes a 40 °C rise from DC alone. AC ripple raises the winding temperature further, and the derating curves in the data sheet are there for exactly that case.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 0.36 mOhm becomes roughly 0.509 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: on a low-voltage rail the DCR drop is a real fraction of the output. Compare the millivolt drop at rated current against the converter tolerance before choosing the smallest inductance in the family.

    • Confirm the pad layout against the drawing: the terminal geometry sets the solder fillet and therefore the thermal path.
    • At frequencies above a few hundred kilohertz, check the AC resistance rise before assuming the DC figure holds.
    • Keep the peak current inside the saturation boundary with margin for inductance tolerance.

    Frequently Asked Questions

    Can this replace a powdered-core part of the same value?
    Only if the saturation behaviour is acceptable. Ferrite saturates abruptly compared with a powder core, so the transient margin has to be re-checked even when the inductance and DCR look similar.

    Can this replace a powdered-core part of the same value?
    Only if the saturation behaviour is acceptable. Ferrite saturates abruptly compared with a powder core, so the transient margin has to be re-checked even when the inductance and DCR look similar.

    Why foil instead of round wire?
    At high frequency the current crowds into the surface of the conductor. A flat foil presents a wide surface for the same cross-section, so the AC resistance stays closer to the DC value and the winding runs cooler.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products